CTZ3E-05A-W1-PF AVX Corporation, CTZ3E-05A-W1-PF Datasheet - Page 5

• Manufacturer Part Number: CTZ3E-05A-W1-PF
• Description: CAP TRIM 1.5-5PF TOP ADJUST SMD
• Manufacturer: AVX Corporation
• Series: CTZ, Kyocerar

Specifications of CTZ3E-05A-W1-PF

• Adjustment Type: Top Adjustment
• Capacitance Range: 1.5 ~ 5pF
• Voltage - Rated: 25V
• Size / Dimension: Rectangular - 0.177" L x 0.126" W (4.50mm x 3.20mm)
• Height: 0.071" (1.80mm)
• Mounting Type: Surface Mount
• Features: Low Profile
• Package / Case: 0.177" L x 0.126" W x 0.071" H (4.50mm x 3.20mm x 1.80mm)
• Capacitance Tolerance: +100, -0%
• Voltage Rating: 25VDC
• Capacitor Dielectric Type: Ceramic
• No. Of Pins: 2
• Capacitor Mounting: SMD
• Application: For AV equipment, cellular phone, cordless phone, TCXO, keyless entry
• Brand/series: CTZ3 Series
• Capacitance: 5 pF
• Case Type: Reflow Washable
• Insulation Resistance: 10000 Megohms
• Insulation Resistance, Test Condition: (Min.)
• Lead Specification: Lead Forming Type (CTZ3 Type)
• Package Type: Direction Taping
• Pin Head Type: Plus Slot
• Temperature Coefficient: NPO ±500 ppm⁄°C
• Temperature, Operating, Maximum: 85 °C
• Temperature, Operating, Minimum: -40 °C
• Torque: 10 to 150 gcm
• Voltage, Rating: 25 VDC
• Maximum Height: 1.8 mm
• Termination Type: SMD
• Rohs Compliant: Yes
• Filter Terminals: SMD
• Capacitance Max: 5pF
• Capacitance Min: 1.5pF
• Operating Temperature Range: -40°C To +85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 478-4700-2; CTZ3E-05A-W1-PF

Multilayer Ceramic Chip Trimmer Capacitors
CTZ2/CTZ3 Series
Recommended Cleaning Precautions for CTZ-E types only
1) When washing with solution (IPA), follow conditions below:
2) When revolving, the silicon coating will break and the torque will increase. This is not irregular. Once the silicon coating breaks, the torque
Recommended Washing Conditions
Test Methods
AK225
AK14lb
Pine Alph (ST100S)
Clean slough (750H)
San Elec (FS813D)
Techno Care
Terpene Cleaner (EC-7R)
IPA
Methylene Chloride
Hot Water
a) Ultrasound wave washing under 1 minute.
b) Soak washing under 5 minutes. However, if using both ultrasound and soak washing, the total washing time should be under 3 minutes.
will return to normal value.
Humidity Test
High Temperature
Load Test
Temperature
Cycling Test
Vibration Test
Shock Resistance
Test
Solderability
Resistance to
Solder Heat Test
Low Temperature
Exposure
Mechanical Load
Setting Drift
Solvent
Item
Asahi Glass Company
Asahi Glass Company
Arakawa Chemical Industries, Ltd.
KAO Corporation
Sanyo Chemical Industries, Ltd.
Toshiba
Alpha Metals
no problem observed
coverage
termination end
IR : 103M
IR : 103M
IR : 103M
IR : 103 M
IR : 103M
IR : 103M
Q : 250 Min.
C :
Q : 150 Min
C :
Q : 200 Min.
C :
Q : 200 Min.
C :
C :
Q : 250 Min.
C :
Q : 250 Min.
C :
C :
Specification
10% Max
5% Max.
7% Max.
5% Max.
10% Max.
5% Max.
5% Max.
5% Max.
Maker
75% ea.
Min
Min.
Min.
Min.
Min.
Min
11
Expose at 40 2 C, 90~95% RH for 96 4 hours
and keep at normal conditions for 1 hour
Vibration frequency range: 10~55Hz
Time: 2 hours each in three different vertical directions
Amplitude: 1.5 mm
Immerse in Pb-Sn solder at 230 5 C for 5 +1/-0 seconds
Apply a 100 gram load in the axis of the rotor
Apply 2
chamber for 96 4 hours and keep at normal conditions
for 24 hours
Perform 5 cycles as follows:
-25 C (30 min.)
(30 min.) and keep at normal conditions for 24 1 hour
Fix on 50 gram metal case and drop onto the concrete
floor from a height of 1 meter
Put on a hot plate at 270 5 C for 5 1 seconds
and keep at normal conditions for 24 hours
Expose in low temperature chamber at -25 C for 96 4 hours
and keep at normal conditions for 1 hour
Rotate rotor 3 times until rotor slot is perpendicular to
mounting pads, at 10 rpm. After that, take an initial
reading of capacitance after 5 seconds.
Measure again after 1 hour
Immerse 50 ~ 55 C 5 min.
Immerse 32 1 C 5 min.
Immerse 70 1 C
Immerse into water 60 1 C 3 min.
Immerse 60 C. 5 min.
Rinse with pure water. Dry 85 C
Immerse 60 C 5 min. Dry 85 C 10min.
Immerse into FRW17 (ultrasonic 10 min)
Rinse out of FRW1 (ultrasonic 3 min)
Immerse room temperature 10 min. and
ultrasonic 2 min. Rinse with water 40~50 C
Immerse room temperature 1 min.
Immerse room temperature 10 min.
Immerse 65 C 10 min.
(X, Y and Z axes, total 6 hours)
rated voltage at 85 3 C in high temperature
Measuring Condition
Measuring Condition
room temperature (5 min.)
+85 C
Results
O.K.
O.K.
O.K.
O.K.
O.K.
O.K.
O.K.
O.K.
O.K.
O.K.