ATTINY2313-20PU Atmel, ATTINY2313-20PU Datasheet - Page 170

• Manufacturer Part Number: ATTINY2313-20PU
• Description: IC MCU AVR 2K FLASH 20DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313-20PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Package: 20PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 18
• Interface Type: SPI/USART/USI
• Number Of Timers: 2
• Processor Series: ATTINY2x
• Core: AVR8
• Data Ram Size: 128 B
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Cpu Family: ATtiny
• Device Core Size: 8b
• Frequency (max): 20MHz
• Total Internal Ram Size: 128Byte
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 20
• Package Type: PDIP
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Reading the
Calibration Byte
Parallel Programming
Characteristics
170
ATtiny2313
The algorithm for reading the Calibration byte is as follows (refer to
page 165
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte, 0x00.
3. Set OE to “0”, and BS1 to “1”. The Calibration byte can now be read at DATA.
4. Set OE to “1”.
Figure 75. Parallel Programming Timing, Including some General Timing Requirements
Figure 76. Parallel Programming Timing, Loading Sequence with Timing Requirements
Note:
PAGEL
XTAL1
(DATA, XA0/1, BS1, BS2)
DATA
BS1
XA0
XA1
1. The timing requirements shown in
for details on Command and Address loading):
operation.
Data & Contol
RDY/BSY
ADDR0 (Low Byte)
LOAD ADDRESS
PAGEL
XTAL1
(LOW BYTE)
WR
t
t
BVPH
DVXH
(LOW BYTE)
LOAD DATA
DATA (Low Byte)
t
t
XHXL
PHPL
Figure 75
t
t
t
t
t
XLXH
XLDX
PLBX
XLWL
PLWL
(i.e., t
t
BVWL
(HIGH BYTE)
LOAD DATA
DVXH
DATA (High Byte)
t
, t
WLWH
t
XLPH
WLRL
XHXL
LOAD DATA
, and t
“Programming the Flash” on
t
PLXH
t
XLDX
WLBX
) also apply to loading
LOAD ADDRESS
(LOW BYTE)
ADDR1 (Low Byte)
2543L–AVR–08/10
t
WLRH
(1)