ATTINY2313-20PU Atmel, ATTINY2313-20PU Datasheet - Page 48

• Manufacturer Part Number: ATTINY2313-20PU
• Description: IC MCU AVR 2K FLASH 20DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313-20PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Package: 20PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 18
• Interface Type: SPI/USART/USI
• Number Of Timers: 2
• Processor Series: ATTINY2x
• Core: AVR8
• Data Ram Size: 128 B
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Cpu Family: ATtiny
• Device Core Size: 8b
• Frequency (max): 20MHz
• Total Internal Ram Size: 128Byte
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 20
• Package Type: PDIP
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Switching Between
Input and Output
Reading the Pin Value
48
ATtiny2313
When switching between tri-state ({DDxn, PORTxn} = 0b00) and output high ({DDxn, PORTxn}
= 0b11), an intermediate state with either pull-up enabled {DDxn, PORTxn} = 0b01) or output
low ({DDxn, PORTxn} = 0b10) must occur. Normally, the pull-up enabled state is fully accept-
able, as a high-impedant environment will not notice the difference between a strong high driver
and a pull-up. If this is not the case, the PUD bit in the MCUCR Register can be set to disable all
pull-ups in all ports.
Switching between input with pull-up and output low generates the same problem. The user
must use either the tri-state ({DDxn, PORTxn} = 0b00) or the output high state ({DDxn, PORTxn}
= 0b11) as an intermediate step.
Table 22
Table 22. Port Pin Configurations
Independent of the setting of Data Direction bit DDxn, the port pin can be read through the
PINxn Register bit. As shown in
tute a synchronizer. This is needed to avoid metastability if the physical pin changes value near
the edge of the internal clock, but it also introduces a delay.
the synchronization when reading an externally applied pin value. The maximum and minimum
propagation delays are denoted t
Figure 23. Synchronization when Reading an Externally Applied Pin value
DDxn
0
0
0
1
1
INSTRUCTIONS
SYSTEM CLK
SYNC LATCH
summarizes the control signals for the pin value.
PORTxn
0
1
1
0
1
PINxn
r17
(in MCUCR)
PUD
X
X
X
0
1
Figure
pd,max
Output
Output
XXX
Input
Input
Input
I/O
and t
22, the PINxn Register bit and the preceding latch consti-
Pull-up
pd,min
Yes
No
No
No
No
t
pd, max
0x00
respectively.
XXX
Comment
Tri-state (Hi-Z)
Pxn will source current if ext. pulled
low.
Tri-state (Hi-Z)
Output Low (Sink)
Output High (Source)
t
pd, min
Figure 23
in r17, PINx
shows a timing diagram of
0xFF
2543L–AVR–08/10