DSPIC33FJ12MC201-I/SO Microchip Technology, DSPIC33FJ12MC201-I/SO Datasheet - Page 21

• Manufacturer Part Number: DSPIC33FJ12MC201-I/SO
• Description: IC DSPIC MCU/DSP 12K 20SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ12MC201-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 12KB (12K x 8)
• Package / Case: 20-SOIC (7.5mm Width)
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 15
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC33F
• Core: dsPIC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 15
• Data Ram Size: 1 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

3.6.2
Configuration bits may be programmed a single byte at
a time using the PROGC command. This command
specifies the configuration data and Configuration
register address.
Twelve PROGC commands are required to program all
the Configuration bits. A flowchart for Configuration bit
programming is illustrated in
FIGURE 3-5:
© 2010 Microchip Technology Inc.
Note:
Note 1: For dsPIC33FJ06GS101/102/202, dsPIC33FJ16GS402/404/502/504, dsPIC33FJ32GS406/606/608/610 and
PROGRAMMING METHODOLOGY
If either of the General Code Segment
Code-Protect
programmed to ‘0’, code memory is
code-protected and cannot be read.
Code memory must be verified before
enabling
Section 3.6.4 “CodeGuard™ Security
Configuration
information
Configuration bits.
dsPIC33FJ64GS406/606/608/610 devices, the Configuration address is 0xF80014.
ConfigAddress + 2
ConfigAddress =
CONFIGURATION BIT PROGRAMMING FLOW
read
bits
Figure
about
Bits”
protection.
3-5.
(GSS<1:0>)
for
code-protect
detailed
No
See
is
PROGC response
ConfigAddress
0xF80018?
Send PROGC
Command
PASS?
Start
3.6.3
After the Configuration bits are programmed, the
contents of memory should be verified to ensure that
the programming was successful. Verification requires
the Configuration bits to be read back and compared
against the copy held in the programmer’s buffer. The
READC command reads back the programmed
Configuration bits and verifies that the programming
was successful.
Any unimplemented Configuration bits are read-only
and read as ‘0’. The reserved bits are read-only and
read as ‘1’.
End
Is
Is
Yes
Yes
(1)
ConfigAddress = 0xF80000
PROGRAMMING VERIFICATION
No
Report Error
Failure
DS70152H-page 21