PIC18LF2410-I/SO Microchip Technology, PIC18LF2410-I/SO Datasheet - Page 124

• Manufacturer Part Number: PIC18LF2410-I/SO
• Description: IC MCU FLASH 8KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF2410-I/SO

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Interface: I2C, SPI, USART
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F2X1X/4X1X
12.2
Timer2 also can generate an optional device interrupt.
The Timer2 output signal (TMR2-to-PR2 match)
provides the input for the 4-bit output counter/
postscaler. This counter generates the TMR2 match
interrupt flag which is latched in TMR2IF (PIR1<1>).
The interrupt is enabled by setting the TMR2 Match
Interrupt Enable bit, TMR2IE (PIE1<1>).
A range of 16 postscale options (from 1:1 through 1:16
inclusive) can be selected with the postscaler control
bits, T2OUTPS3:T2OUTPS0 (T2CON<6:3>).
FIGURE 12-1:
TABLE 12-1:
DS39636D-page 126
INTCON GIE/GIEH PEIE/GIEL
PIR1
PIE1
IPR1
TMR2
T2CON
PR2
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer2 module.
Note 1:
Name
T2OUTPS3:T2OUTPS0
T2CKPS1:T2CKPS0
F
OSC
Timer2 Interrupt
/4
Timer2 Register
Timer2 Period Register
These bits are unimplemented on 28-pin devices and read as ‘0’.
PSPIE
PSPIP
PSPIF
Bit 7
—
REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER
(1)
(1)
(1)
TIMER2 BLOCK DIAGRAM
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0
Internal Data Bus
ADIE
ADIP
ADIF
Bit 6
1:1, 1:4, 1:16
2
Prescaler
TMR0IE
RCIF
RCIE
RCIP
Bit 5
4
TMR2
INT0IE
TXIE
TXIP
Bit 4
TXIF
Reset
8
SSPIE
SSPIP
SSPIF
RBIE
Bit 3
12.3
The unscaled output of TMR2 is available primarily to
the CCP modules, where it is used as a time base for
operations in PWM mode.
Timer2 can be optionally used as the shift clock source
for the MSSP module operating in SPI mode. Addi-
tional information is provided in Section 16.0 “Master
Synchronous Serial Port (MSSP) Module”.
Comparator
1:1 to 1:16
Postscaler
8
TMR2/PR2
Match
Timer2 Output
TMR0IF
CCP1IF
CCP1IE
CCP1IP
Bit 2
TMR2IF
TMR2IE
TMR2IP
INT0IF
© 2009 Microchip Technology Inc.
Bit 1
PR2
8
Set TMR2IF
TMR2 Output
(to PWM or MSSP)
TMR1IF
TMR1IE
TMR1IP
RBIF
Bit 0
on page
Values
Reset
51
54
54
54
52
52
52