DSPIC33FJ16GS502-I/SO Microchip Technology, DSPIC33FJ16GS502-I/SO Datasheet - Page 90

• Manufacturer Part Number: DSPIC33FJ16GS502-I/SO
• Description: IC DSPIC MCU/DSP 16K 28-SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16GS502-I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Core Frequency: 40MHz
• Core Supply Voltage: 3.3V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 21
• Flash Memory Size: 16KB
• Supply Voltage Range: 3V To 3.6V
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 6-1:
DS70318D-page 88
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13-10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
Note 1: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not
TRAPR
R/W-0
R/W-0
EXTR
2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
cause a device Reset.
SWDTEN bit setting.
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an
0 = An illegal opcode or uninitialized W Reset has not occurred
Unimplemented: Read as ‘0’
CM: Configuration Mismatch Flag bit
1 = A Configuration Mismatch Reset has occurred
0 = A Configuration Mismatch Reset has NOT occurred
VREGS: Voltage Regulator Standby During Sleep bit
1 = Voltage regulator is active during Sleep
0 = Voltage regulator goes into Standby mode during Sleep
EXTR: External Reset Pin (MCLR) bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
SWR: Software Reset Flag (Instruction) bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit
1 = WDT is enabled
0 = WDT is disabled
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
SLEEP: Wake-up from Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
IDLE: Wake-up from Idle Flag bit
1 = Device was in Idle mode
0 = Device was not in Idle mode
IOPUWR
R/W-0
R/W-0
SWR
Address Pointer caused a Reset
RCON: RESET CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
SWDTEN
R/W-0
U-0
—
(2)
WDTO
R/W-0
U-0
Preliminary
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SLEEP
R/W-0
(2)
U-0
—
(1)
R/W-0
IDLE
U-0
—
© 2009 Microchip Technology Inc.
x = Bit is unknown
R/W-0
R/W-1
BOR
CM
VREGS
R/W-0
R/W-1
POR
bit 8
bit 0