ATMEGA32A-PU Atmel, ATMEGA32A-PU Datasheet - Page 274

• Manufacturer Part Number: ATMEGA32A-PU
• Description: MCU AVR 32K FLASH 16MHZ 40-PDIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32A-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 40PDIP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Rom Size: 1024 B
• Height: 4.83 mm
• Length: 52.58 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 13.97 mm
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8155C–AVR–02/11
8 bits are required to address words in the page (pagesize < 256), the most significant bit(s) in
the address low byte are used to address the page when performing a page write.
G. Load Address High byte
H. Program Page
I. Repeat B through H until the entire Flash is programmed or until all data has been
programmed.
J. End Page Programming
Figure 26-2. Addressing the Flash which is Organized in Pages
Note:
1. Set XA1, XA0 to “00”. This enables address loading.
2. Set BS1 to “1”. This selects high address.
3. Set DATA = Address high byte ($00 - $FF).
4. Give XTAL1 a positive pulse. This loads the address high byte.
1. Set BS1 = “0”
2. Give WR a negative pulse. This starts programming of the entire page of data.
3. Wait until RDY/BSY goes high. (See
1. 1. Set XA1, XA0 to “10”. This enables command loading.
2. Set DATA to “0000 0000”. This is the command for No Operation.
3. Give XTAL1 a positive pulse. This loads the command, and the internal write signals
RDY/BSYgoes low.
are reset.
1. PCPAGE and PCWORD are listed in
PROGRAM MEMORY
PROGRAM
COUNTER
PAGE
PAGE ADDRESS
WITHIN THE FLASH
PCMSB
PCPAGE
PAGEMSB
Figure 26-3
PCWORD
Table 26-5 on page 269
WORD ADDRESS
WITHIN A PAGE
for signal waveforms)
INSTRUCTION WORD
PAGE
.
ATmega32A
PCWORD[PAGEMSB:0]:
00
01
02
PAGEEND
274