DSPIC33FJ128GP206A-I/MR Microchip Technology, DSPIC33FJ128GP206A-I/MR Datasheet - Page 252

IC DSPIC MCU/DSP 128K 64-QFN

DSPIC33FJ128GP206A-I/MR

Manufacturer Part Number
DSPIC33FJ128GP206A-I/MR
Description
IC DSPIC MCU/DSP 128K 64-QFN
Manufacturer
Microchip Technology
Series
dsPIC™ 33Fr
Datasheet

Specifications of DSPIC33FJ128GP206A-I/MR

Core Processor
dsPIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
Number Of I /o
53
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 18x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-VFQFN, Exposed Pad
Product
DSCs
Processor Series
DSPIC33F
Core
dsPIC
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
dsPIC33FJXXXGPX06A/X08A/X10A
22.2
All of the dsPIC33FJXXXGPX06A/X08A/X10A devices
power their core digital logic at a nominal 2.5V. This
may create an issue for designs that are required to
operate at a higher typical voltage, such as 3.3V. To
simplify
dsPIC33FJXXXGPX06A/X08A/X10A
porate an on-chip regulator that allows the device to
run its core logic from V
The regulator provides power to the core from the
other V
low-ESR (less than 5 ohms) capacitor (such as
tantalum or ceramic) be connected to the V
V
the stability of the regulator. The recommended
value
Table 25-13
Characteristics”.
On a POR
voltage regulator to generate an output voltage. During
this time, designated as T
disabled. T
resumes operation after any power-down.
FIGURE 22-1:
DS70593B-page 252
DDCORE
Note 1:
Note:
for
2:
DD
On-Chip Voltage Regulator
C
,
system
pin (Figure 22-1). This helps to maintain
EFC
STARTUP
it takes approximately 20 s for the on-chip
It is important for the low-ESR capacitor to
be placed as close as possible to the
V
These are typical operating voltages. Refer to
Section TABLE 25-13: “Internal Voltage
Regulator Specifications” located in
Section 25.1 “DC Characteristics” for the
full operating ranges of V
V
It is important for the low-ESR capacitor to be
placed as close as possible to the V
the
pins. The regulator requires that a
CAP
DDCORE
3.3V
/V
of
filter
DDCORE
design,
is applied every time the device
.
CONNECTIONS FOR THE
ON-CHIP VOLTAGE
REGULATOR
V
V
V
DD
Section 25.0
DD
CAP
SS
capacitor
dsPIC33F
.
STARTUP
pin.
/V
DDCORE
all
DD
, code execution is
devices
is
and V
(1)
family
provided
CAP
“Electrical
CAP
/
in
/
incor-
CAP
Preliminary
the
in
/
22.3
The BOR (Brown-out Reset) module is based on an
internal voltage reference circuit that monitors the
regulated voltage V
the BOR module is to generate a device Reset when a
brown-out condition occurs. Brown-out conditions are
generally caused by glitches on the AC mains (i.e.,
missing portions of the AC cycle waveform due to bad
power transmission lines or voltage sags due to
excessive current draw when a large inductive load is
turned on).
A BOR will generate a Reset pulse which will reset the
device. The BOR will select the clock source, based on
the device Configuration bit values (FNOSC<2:0> and
POSCMD<1:0>). Furthermore, if an oscillator mode is
selected, the BOR will activate the Oscillator Start-up
Timer (OST). The system clock is held until OST
expires. If the PLL is used, then the clock will be held
until the LOCK bit (OSCCON<5>) is ‘1’.
Concurrently, the PWRT time-out (TPWRT) will be
applied before the internal Reset is released. If
TPWRT = 0 and a crystal oscillator is being used, then
a nominal delay of TFSCM = 100 is applied. The total
delay in this case is TFSCM.
The BOR Status bit (RCON<1>) will be set to indicate
that a BOR has occurred. The BOR circuit continues to
operate while in Sleep or Idle modes and will reset the
device should VDD fall below the BOR threshold
voltage.
BOR: Brown-out Reset
CAP
/V
 2009 Microchip Technology Inc.
DDCORE
. The main purpose of

Related parts for DSPIC33FJ128GP206A-I/MR