ATMEGA1284P-PU Atmel, ATMEGA1284P-PU Datasheet - Page 38

MCU AVR 128K ISP FLASH 40-PDIP

ATMEGA1284P-PU

Manufacturer Part Number
ATMEGA1284P-PU
Description
MCU AVR 128K ISP FLASH 40-PDIP
Manufacturer
Atmel
Series
AVR® ATmegar

Specifications of ATMEGA1284P-PU

Core Processor
AVR
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
128KB (64K x 16)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Processor Series
ATMEGA128x
Core
AVR8
Data Bus Width
8 bit
Data Ram Size
16 KB
Interface Type
2-Wire/SPI/USART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
32
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRRAVEN, ATAVRRZUSBSTICK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
Controller Family/series
AVR MEGA
No. Of I/o's
32
Eeprom Memory Size
4KB
Ram Memory Size
16KB
Cpu Speed
20MHz
Rohs Compliant
Yes
For Use With
ATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600 - DEV KIT FOR AVR/AVR32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA1284P-PU
Manufacturer:
LUCENT
Quantity:
32
8.7
8.8
8272A–AVR–01/10
128 kHz Internal Oscillator
External Clock
The 128 kHz internal Oscillator is a low power Oscillator providing a clock of 128 kHz. The fre-
quency is nominal at 3V and 25°C. This clock may be select as the system clock by
programming the CKSEL Fuses to “0011” as shown in
Table 8-12.
Note:
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 8-13.
To drive the device from an external clock source, XTAL1 should be driven as shown in
8-4. To run the device on an external clock, the CKSEL Fuses must be programmed to “0000”.
Figure 8-4.
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
164A/164PA/324A/324PA/644A/644PA/1284/1284P
BOD enabled
Fast rising power
Slowly rising power
Power Conditions
8-13.
8-15.
1. Note that the 128kHz oscillator is a very low power clock source, and is not designed for high
accuracy.
128 kHz Internal Oscillator Operating Modes
Start-up Times for the 128 kHz Internal Oscillator
External Clock Drive Configuration
Nominal Frequency
EXTERNAL
128 kHz
SIGNAL
CLOCK
Start-up Time from Power-
down and Power-save
NC
Reserved
6 CK
6 CK
6 CK
XTAL2
XTAL1
GND
Table
(2)
Additional Delay from
8-12.
14CK + 64 ms
14CK + 4 ms
Reset
14CK
CKSEL3..0
0011
SUT1..0
00
01
10
11
Figure
38

Related parts for ATMEGA1284P-PU