DSPIC33FJ128GP708-I/PT Microchip Technology, DSPIC33FJ128GP708-I/PT Datasheet - Page 20

• Manufacturer Part Number: DSPIC33FJ128GP708-I/PT
• Description: IC DSPIC MCU/DSP 128K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128GP708-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (128K x 8)
• Package / Case: 80-TFQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 69
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 24x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC33F
• Core: dsPIC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 69
• Data Ram Size: 16 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1001 - DSPIC33 BREAKOUT BOARDDM300024 - KIT DEMO DSPICDEM 1.1DV164033 - KIT START EXPLORER 16 MPLAB ICD2MA330012 - MODULE DSPIC33 100P TO 84QFPMA330011 - MODULE DSPIC33 100P TO 100QFPDM300019 - BOARD DEMO DSPICDEM 80L STARTERDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164328 - MODULE SKT FOR 80TQFPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

43. Module: UART
44. Module: SPI
45. Module: I
DS80446D-page 20
When the UART is configured for IR interface
operations (UxMODE<9:8> = 11), the 16x baud
clock signal on the BCLK pin is present only when
the module is transmitting. The pin is idle at all
other times.
Work around
Configure one of the output compare modules to
generate the required baud clock signal when the
UART is receiving data or in an Idle state.
Affected Silicon Revisions
Setting the DISSCK bit in the SPIxCON1 register
does not allow the user application to use the SCK
pin as a general purpose I/O pin.
Work around
None.
Affected Silicon Revisions
The BCL bit in I2CSTAT can be cleared only with
16-bit operation, and can be corrupted with 1-bit or
8-bit operations on I2CSTAT.
Work around
Use 16-bit operations to clear BCL.
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
2
C
A4
A4
A4
X
X
X
46. Module: I
47. Module: I
48. Module: I
If there are two I
them acts as the master receiver and the other
acts as the slave transmitter. If both devices are
configured for 10-bit Addressing mode, and have
the same value in the A10 and A9 bits of their
addresses: then, when the slave select address is
sent from the master, both the master and slave
acknowledge it. When the master sends out the
read operation, both the master and the slave
enter into Read mode, and both of them transmit
the data. The resultant data will be the ANDing of
the two transmissions.
Work around
In all I
A10 and A9, should be different.
Affected Silicon Revisions
If the I
with an address of 0x102, the I2CxRCV register
content for the lower address byte is 0x01, rather
than
acknowledges both address bytes.
Work around
None.
Affected Silicon Revisions
With the I
external
associated with the SCL and SDA pins do not
reflect the actual digital logic levels on the pins.
Work around
If the SDA and/or SCL pins need to be polled,
these pins should be connected to other port pins
in order to be read correctly. This issue does not
affect the operation of the I
Affected Silicon Revisions
A2
A2
A2
X
X
X
2
2
C devices, the addresses, as well as bits
0x02.
A3
C module is configured as a 10-bit slave
A3
A3
X
X
X
2
interrupt
C module enabled, the PORT bits and
2
2
2
C
C
C
A4
A4
A4
X
X
X
However,
2
C devices on the bus, one of
© 2010 Microchip Technology Inc.
input
2
C module.
functions
the
I
2
C
(if
module
any)