DSPIC33FJ128GP708A-I/PT Microchip Technology, DSPIC33FJ128GP708A-I/PT Datasheet - Page 177

• Manufacturer Part Number: DSPIC33FJ128GP708A-I/PT
• Description: IC DSPIC MCU/DSP 128K 80-TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128GP708A-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (128K x 8)
• Package / Case: 80-TFQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 69
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 24x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC33F
• Core: dsPIC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 69
• Data Ram Size: 16 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
• Minimum Operating Temperature: - 40 C
• Package: 80TQFP
• Device Core: dsPIC
• Family Name: dsPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 48-chx10-bit|48-chx12-bit
• Number Of Timers: 9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1001 - DSPIC33 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

15.0
FIGURE 15-1:
 2009 Microchip Technology Inc.
Note 1: This data sheet summarizes the features
Note 1:
2: Some registers and associated bits
OUTPUT COMPARE
of
X10A families of devices. It is not
intended to be a comprehensive refer-
ence source. To complement the informa-
tion in this data sheet, refer to Section
13. “Output Compare” (DS70209) of the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
described in this section may not be avail-
able on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
2: The OCFA pin controls OC1 through OC4. The OCFB pin controls OC5 through OC8.
the dsPIC33FJXXXGPX06A/X08A/
An ‘x’ in a signal, register or bit name denotes the number of the output compare channels.
OUTPUT COMPARE MODULE BLOCK DIAGRAM
16
TMR2
dsPIC33FJXXXGPX06A/X08A/X10A
OCxRS
Comparator
OCxR
0
TMR3
(1)
(1)
1
16
OCTSEL
Rollover Rollover
TMR2
Preliminary
0
TMR3
1
The output compare module can select either Timer2 or
Timer3 for its time base. The module compares the
value of the timer with the value of one or two Compare
registers depending on the operating mode selected.
The state of the output pin changes when the timer
value matches the Compare register value. The output
compare module generates either a single output
pulse, or a sequence of output pulses, by changing the
state of the output pin on the compare match events.
The output compare module can also generate inter-
rupts on compare match events.
The output compare module has multiple operating
modes:
• Active-Low One-Shot mode
• Active-High One-Shot mode
• Toggle mode
• Delayed One-Shot mode
• Continuous Pulse mode
• PWM mode without Fault Protection
• PWM mode with Fault Protection
Mode Select
OCM<2:0>
Output
Logic
3
Set Flag bit
OCxIF
(1)
R
S
Q
Output Enable
DS70593B-page 177
OCx
OCFA
or
OCFB
(1)
(2)