AT32UC3A0128-ALUT Atmel, AT32UC3A0128-ALUT Datasheet - Page 108

• Manufacturer Part Number: AT32UC3A0128-ALUT
• Description: IC MCU AVR32 128KB FLASH 144LQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3A0128-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 109
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: 2-Wire, RS-485, SPI, USART
• Maximum Clock Frequency: 66 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL, KSK-EVK1100-PL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATEXTWIFI, ATEVK1100, ATEVK1105
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AT32UC3A
• No. Of I/o's: 109
• Ram Memory Size: 32KB
• Cpu Speed: 66MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• For Use With: ATEVK1105 - KIT EVAL FOR AT32UC3A0ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1100 - KIT DEV/EVAL FOR AVR32 AT32UC3A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

17.5.3
32058J–AVR32–04/11
Keypad scan support
The NMI is non-maskable within the CPU in the sense that it can interrupt any other execution
mode. Still, as for the other external interrupts, the actual NMI input line can be enabled and dis-
abled by accessing the registers in the External Interrupt Module. These interrupts are not
enabled by default, allowing the proper interrupt vectors to be set up by the CPU before the
interrupts are enabled.
The External Interrupt Module also includes support for keypad scanning. The keypad scan fea-
ture is compatible with keypads organized as rows and columns, where a row is shorted against
a column when a key is pressed.
The rows should be connected to the external interrupt pins with pullups enabled in the GPIO
module. These external interrupts should be enabled as low level or falling edge interrupts. The
columns should be connected to the available scan pins. The GPIO must be configured to let the
required scan pins be controlled by the EIC module. Unused external interrupt or scan pins can
be left controlled by the GPIO or other peripherals.
The Keypad Scan function is enabled by writing :EN to 1, which starts the keypad scan counter.
The SCAN outputs are tristated, except SCAN[0], which is driven to zero. After 2
RC clock cycles this pattern is left shifted, so that SCAN[1] is driven to zero while the other out-
puts are tristated. This sequence repeats infinitely, wrapping from the most significant SCAN pin
to SCAN[0].
When a key is pressed, the pulled-up row is driven to zero by the column, and an external inter-
rupt triggers. The scanning stops, and the software can then identify the key pressed by the
interrupt status register and the SCAN:PINS value.
The scanning stops whenever there is an active interrupt request from the EIC to the CPU.
When the CPU clears the interrupt flags, scanning resumes.
AT32UC3A
(SCAN:PRESC+1)
108