AT32UC3A0128-ALUT Atmel, AT32UC3A0128-ALUT Datasheet - Page 196

• Manufacturer Part Number: AT32UC3A0128-ALUT
• Description: IC MCU AVR32 128KB FLASH 144LQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3A0128-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 109
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: 2-Wire, RS-485, SPI, USART
• Maximum Clock Frequency: 66 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL, KSK-EVK1100-PL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATEXTWIFI, ATEVK1100, ATEVK1105
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AT32UC3A
• No. Of I/o's: 109
• Ram Memory Size: 32KB
• Cpu Speed: 66MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• For Use With: ATEVK1105 - KIT EVAL FOR AT32UC3A0ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1100 - KIT DEV/EVAL FOR AVR32 AT32UC3A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

23.7
23.7.1
23.7.2
32058J–AVR32–04/11
Functional Description
Modes of Operation
Data Transfer
The SPI operates in Master Mode or in Slave Mode.
Operation in Master Mode is programmed by writing at 1 the MSTR bit in the Mode Register.
The pins NPCS0 to NPCS3 are all configured as outputs, the SPCK pin is driven, the MISO line
is wired on the receiver input and the MOSI line driven as an output by the transmitter.
If the MSTR bit is written at 0, the SPI operates in Slave Mode. The MISO line is driven by the
transmitter output, the MOSI line is wired on the receiver input, the SPCK pin is driven by the
transmitter to synchronize the receiver. The NPCS0 pin becomes an input, and is used as a
Slave Select signal (NSS). The pins NPCS1 to NPCS3 are not driven and can be used for other
purposes.
The data transfers are identically programmable for both modes of operations. The baud rate
generator is activated only in Master Mode.
Four combinations of polarity and phase are available for data transfers. The clock polarity is
programmed with the CPOL bit in the Chip Select Register. The clock phase is programmed with
the NCPHA bit. These two parameters determine the edges of the clock signal on which data is
driven and sampled. Each of the two parameters has two possible states, resulting in four possi-
ble combinations that are incompatible with one another. Thus, a master/slave pair must use the
same parameter pair values to communicate. If multiple slaves are used and fixed in different
configurations, the master must reconfigure itself each time it needs to communicate with a dif-
ferent slave.
Table 23-2
Table 23-2.
Figure 23-3
shows the four modes and corresponding parameter settings.
and
SPI Bus Protocol Mode
Figure 23-4
SPI Mode
0
1
2
3
show examples of data transfers.
CPOL
0
0
1
1
AT32UC3A
NCPHA
1
0
1
0
196