AT32UC3A0256-ALUT Atmel, AT32UC3A0256-ALUT Datasheet - Page 506

• Manufacturer Part Number: AT32UC3A0256-ALUT
• Description: IC MCU AVR32 256KB FLASH 144LQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3A0256-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 109
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: 2-Wire, RS-485, SPI, USART
• Maximum Clock Frequency: 66 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL, KSK-EVK1100-PL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATEXTWIFI, ATEVK1100, ATEVK1105
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AT32UC3A
• No. Of I/o's: 109
• Ram Memory Size: 64KB
• Cpu Speed: 66MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Package: 144LQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 66 MHz
• Operating Supply Voltage: 1.8|3.3 V
• For Use With: ATEVK1105 - KIT EVAL FOR AT32UC3A0ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1100 - KIT DEV/EVAL FOR AVR32 AT32UC3A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

30.7.1.4.6
30.7.1.5
30.7.1.5.1
Figure 30-7. Speed Selection in Device Mode
30.7.1.5.2
30.7.1.6
32058J–AVR32–04/11
USB Suspend mode :
Speed Control
DPRAM Management
Device Mode
Host Mode
In peripheral mode, the UDINT.SUSP bit indicates that the usb line is in the suspend mode. In
this case, the USB Data transceiver is automatically set in suspend mode to reduce the
consumption.
When the USB interface is in device mode, the speed selection (full-/low-speed) depends on
which of D+ and D- is pulled up. The LS bit allows to connect an internal pull-up resistor either
on D+ (full-speed mode) or on D- (low-speed mode). The LS bit should be configured before
attaching the device, what can be done by clearing the DETACH bit.
When the USB interface is in host mode, internal pull-down resistors are connected on both D+
and D- and the interface detects the speed of the connected device, which is reflected by the
SPEED bit-field.
Pipes and endpoints can only be allocated in ascending order (from the pipe/endpoint 0 to the
last pipe/endpoint to be allocated). The firmware shall therefore configure them in the same
order.
The allocation of a pipe/endpoint k
cates a memory area in the DPRAM and inserts it between the k
k
point memory windows (from k
i+1
•the VBus Transition interrupt (VBUSTI);
•the Wake-Up interrupt (WAKEUP);
•the Host Wake-Up interrupt (HWUPI).
pipe/endpoint memory window slides up and its data is lost. Note that the following pipe/end-
VBUS
D+
D-
i+2
) do not slide.
i
starts when its ALLOC bit is set. Then, the hardware allo-
UDCON.DETACH
UDCON.LS
i-1
and k
i+1
pipes/endpoints. The
AT32UC3A
506