AT32UC3A0256-ALUT Atmel, AT32UC3A0256-ALUT Datasheet - Page 576

• Manufacturer Part Number: AT32UC3A0256-ALUT
• Description: IC MCU AVR32 256KB FLASH 144LQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3A0256-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 109
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: 2-Wire, RS-485, SPI, USART
• Maximum Clock Frequency: 66 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL, KSK-EVK1100-PL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATEXTWIFI, ATEVK1100, ATEVK1105
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AT32UC3A
• No. Of I/o's: 109
• Ram Memory Size: 64KB
• Cpu Speed: 66MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Package: 144LQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 66 MHz
• Operating Supply Voltage: 1.8|3.3 V
• For Use With: ATEVK1105 - KIT EVAL FOR AT32UC3A0ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1100 - KIT DEV/EVAL FOR AVR32 AT32UC3A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

For OUT endpoints, it indicates the number of banks filled by OUT transactions from the host. When all banks are busy,
this triggers an EPXINT interrupt if NBUSYBKE = 1.
Note that when the FIFOCON bit is cleared (by setting the FIFOCONC bit) to validate a new bank, this field is updated 2 or
3 clock cycles later to calculate the address of the next bank.
An EPXINT interrupt is triggered if :
- for IN endpoint, NBUSYBKE=1 and all the banks are free.
- for OUT endpoint, NBUSYBKE=1 and all the banks are busy.
• CURRBK: Current Bank
For non-control endpoints, set by hardware to indicate the current bank:
Note that this field may be updated 1 clock cycle after the RWALL bit changes, so the user should not poll this field as an
interrupt flag.
• RWALL: Read/Write Allowed
For IN endpoints, set by hardware when the current bank is not full, i.e. the software can write further data into the FIFO.
For OUT endpoints, set by hardware when the current bank is not empty, i.e. the software can read further data from the
FIFO.
Never set if STALLRQ = 1 or in case of error.
Cleared by hardware otherwise.
This bit shall not be used for control endpoints.
• CTRLDIR: Control Direction
Set by hardware after a SETUP packet to indicate the direction of the following packet:
Can not be set or cleared by software.
• CFGOK: Configuration OK Status
This bit is updated when the ALLOC bit is set.
Set by hardware if the endpoint X number of banks (EPBK) and size (EPSIZE) are correct compared to the maximal
allowed number of banks and size for this endpoint and to the maximal FIFO size (i.e. the DPRAM size).
If this bit is cleared by hardware, the user should reprogram the UECFGX register with correct EPBK and EPSIZE values.
• BYCT: Byte Count
Set by the hardware to indicate the byte count of the FIFO.
32058J–AVR32–04/11
0
0
1
1
CTRLDIR
CURRBK
0
1
0
1
0
1
Control Direction
OUT
IN
Current Bank
Bank0
Bank1
Bank2
Reserved
AT32UC3A
576