ST62T03CM6 STMicroelectronics, ST62T03CM6 Datasheet - Page 13

• Manufacturer Part Number: ST62T03CM6
• Description: IC MCU 8BIT W/ADC 16-SOP
• Manufacturer: STMicroelectronics
• Series: ST6r

Specifications of ST62T03CM6

• Core Processor: ST6
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, WDT
• Number Of I /o: 9
• Program Memory Size: 1KB (1K x 8)
• Program Memory Type: OTP
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Controller Family/series: ST6
• No. Of I/o's: 9
• Ram Memory Size: 64Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Processor Series: ST62T0x
• Core: ST6
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 9
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST622XC-KIT/110, ST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-8233; ST62T03CM6

MEMORY MAP (Cont’d)
3.1.6.2 Data ROM Window memory addressing
In cases where some data (look-up tables for ex-
ample) are stored in program memory, reading
these data requires the use of the Data ROM win-
dow mechanism. To do this:
1. The DRWR register has to be loaded with the
64-byte block number where the data are located
(in program memory). This number also gives the
start address of the block.
2. Then, the offset address of the byte in the Data
ROM Window (corresponding to the offset in the
64-byte block in program memory) has to be load-
ed in a register (A, X,...).
When the above two steps are completed, the
data can be read.
To understand how to determine the DRWR and
the content of the register, please refer to the ex-
ample shown in
Figure 6. Data ROM Window Memory Addressing
OFFSET
DATA address in Program memory : 421h
DRWR content : 421h / 3Fh (64) = 10H data is located in 64-bytes window number 10h
64-byte window start address : 10h x 3Fh = 400h
Register (A, X,...)content : Offset = (421h - 400h) + 40h ( Data ROM Window start address in data space) = 61h
0000h
0400h
0421h
07FFh
PROGRAM SPACE
Figure
64 bytes
DATA
6. In any case the calcula-
Doc ID 4563 Rev 5
tion is automatically handled by the ST6 develop-
ment tools.
Please refer to the user manual of the correspod-
ing tool.
3.1.6.3 Recommendations
Care is required when handling the DRWR regis-
ter as it is write only. For this reason, the DRWR
contents should not be changed while executing
an interrupt service routine, as the service routine
cannot save and then restore the register’s previ-
ous contents. If it is impossible to avoid writing to
the DRWR during the interrupt service routine, an
image of the register must be saved in a RAM lo-
cation, and each time the program writes to the
DRWR, it must also write to the image register.
The image register must be written first so that, if
an interrupt occurs between the two instructions,
the DRWR is not affected.
DATA SPACE
10h
ST6200C ST6201C ST6203C
DATA
DRWR
0FFh
07Fh
000h
040h
061h
OFFSET
21h
13/100
1