MCU 32KB FLASH EEPROM 32-VFQFPN

STM8S105K6U6

Manufacturer Part NumberSTM8S105K6U6
DescriptionMCU 32KB FLASH EEPROM 32-VFQFPN
ManufacturerSTMicroelectronics
SeriesSTM8S
STM8S105K6U6 datasheet
 


Specifications of STM8S105K6U6

Core ProcessorSTM8Core Size8-Bit
Speed16MHzConnectivityI²C, IrDA, LIN, SPI, UART/USART
PeripheralsBrown-out Detect/Reset, POR, PWM, WDTNumber Of I /o25
Program Memory Size32KB (32K x 8)Program Memory TypeFLASH
Eeprom Size1K x 8Ram Size2K x 8
Voltage - Supply (vcc/vdd)2.95 V ~ 5.5 VData ConvertersA/D 7x10b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case32-VFQFN, 32-VFQFPNProcessor SeriesSTM8S10x
CoreSTM8Data Bus Width8 bit
Data Ram Size2 KBInterface TypeI2C, SPI, UART
Maximum Clock Frequency16 MHzNumber Of Programmable I/os25
Number Of Timers8Maximum Operating Temperature+ 85 C
Mounting StyleSMD/SMT3rd Party Development ToolsEWSTM8
Development Tools By SupplierSTICE-SYS001Minimum Operating Temperature- 40 C
On-chip Adc10 bit, 7 ChannelFor Use With497-10040 - EVAL KIT STM8S DISCOVERY497-10593 - KIT STARTER FOR STM8S207/8 SER
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names497-10123
STM8S105K6U6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Page 51
52
Page 52
53
Page 53
54
Page 54
55
Page 55
56
Page 56
57
Page 57
58
Page 58
59
Page 59
60
Page 60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Page 59/127

Download datasheet (2Mb)Embed
PrevNext
STM8S105xx
Symbol
Ratings
(4) (5)
I
INJ(PIN)
(4)
ΣI
INJ(PIN)
(1)
Data based on characterization results, not tested in production.
(2)
All power (V
DD
connected to the external supply.
(3)
I/O pins used simultaneously for high current source/sink must be uniformly spaced
around the package between the V
(4)
I
must never be exceeded. This is implicitly insured if V
INJ(PIN)
If V
maximum cannot be respected, the injection current must be limited externally to the
IN
I
value. A positive injection is induced by V
INJ(PIN)
by V
<V
. For true open-drain pads, there is no positive injection current, and the
IN
SS
corresponding V
(5)
Negative injection disturbs the analog performance of the device. See note in
characteristics.
(6)
When several inputs are submitted to a current injection, the maximum ΣI
absolute sum of the positive and negative injected currents (instantaneous values). These
results are based on characterization with ΣI
port pins of the device.
Symbol
T
STG
T
J
10.3
Operating conditions
The device must be used in operating conditions that respect the parameters in the table
below. In addition, full account must be taken of all physical capacitor characteristics and
tolerances.
Injected current on NRST pin
Injected current on OSCIN pin
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
, V
, V
) and ground (V
DDIO
DDA
/V
DDIO
SSIO
maximum must always be respected
IN
INJ(PIN)
Table 18: Thermal characteristics
Ratings
Storage temperature range
Maximum junction temperature
DocID14771 Rev 10
Electrical characteristics
(1)
Max.
±4
±4
(6)
±4
(6)
±20
, V
, V
) pins must always be
SS
SSIO
SSA
pins.
maximum is respected.
IN
>V
while a negative injection is induced
IN
DD
maximum current injection on four I/O
Value
-65 to 150
150
Unit
I2C interface
is the
INJ(PIN)
Unit
°C
59/127