IC MCU 8BIT OTP 4K 20 PDIP

ST62T20CB6

Manufacturer Part NumberST62T20CB6
DescriptionIC MCU 8BIT OTP 4K 20 PDIP
ManufacturerSTMicroelectronics
SeriesST6
ST62T20CB6 datasheet
 


Specifications of ST62T20CB6

Core ProcessorST6Core Size8-Bit
Speed8MHzPeripheralsLVD, POR, WDT
Number Of I /o12Program Memory Size4KB (4K x 8)
Program Memory TypeOTPRam Size64 x 8
Voltage - Supply (vcc/vdd)3 V ~ 6 VData ConvertersA/D 8x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case20-DIP (0.300", 7.62mm)Controller Family/seriesST6
No. Of I/o's12Ram Memory Size64Byte
Cpu Speed8MHzNo. Of Timers1
Rohs CompliantYesProcessor SeriesST62T2x
CoreST6Data Bus Width8 bit
Data Ram Size64 BMaximum Clock Frequency8 MHz
Number Of Programmable I/os12Number Of Timers2
Operating Supply Voltage3 V to 6 VMaximum Operating Temperature+ 85 C
Mounting StyleThrough HoleDevelopment Tools By SupplierST622XC-KIT/110, ST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
Minimum Operating Temperature- 40 COn-chip Adc8 bit
Lead Free Status / RoHS StatusLead free / RoHS CompliantEeprom Size-
Connectivity-Other names497-2098-5
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
Page 16/104

Download datasheet (2Mb)Embed
PrevNext
ST6208C/ST6209C/ST6210C/ST6220C
3.3 OPTION BYTES
Each device is available for production in user pro-
grammable versions (OTP) as well as in factory
coded versions (ROM). OTP devices are shipped
to customers with a default content (00h), while
ROM factory coded parts contain the code sup-
plied by the customer. This implies that OTP de-
vices have to be configured by the customer using
the Option Bytes while the ROM devices are facto-
ry-configured.
The two option bytes allow the hardware configu-
ration of the microcontroller to be selected.
The option bytes have no address in the memory
map and can be accessed only in programming
mode (for example using a standard ST6 program-
ming tool).
In masked ROM devices, the option bytes are
fixed in hardware by the ROM code (see
11.6.2 "ROM VERSION" on page
fore impossible to read the option bytes.
The option bytes can be only programmed once. It
is not possible to change the selected options after
they have been programmed.
In order to reach the power consumption value in-
dicated in
Section
10.4, the option byte must be
programmed to its default value. Otherwise, an
over-consumption will occur.
MSB OPTION BYTE
Bits 15:10 = Reserved, must be always cleared.
Bit 9 = EXTCNTL External STOP MODE control.
0: EXTCNTL mode not available. STOP mode is
not available with the watchdog active.
1: EXTCNTL mode available. STOP mode is avail-
able with the watchdog active by setting NMI pin
to one.
Bit 8 = LVD Low Voltage Detector on/off.
This option bit enable or disable the Low Voltage
Detector (LVD) feature.
0: Low Voltage Detector disabled
1: Low Voltage Detector enabled
MSB OPTION BYTE
15
Reserved
Default
X
X
X
X
Value
16/104
1
LSB OPTION BYTE
Bit 7 = PROTECT Readout Protection.
This option bit enables or disables external access
to the internal program memory.
0: Program memory not read-out protected
1: Program memory read-out protected
Bit 6 = OSC Oscillator selection.
This option bit selects the main oscillator type.
0: Quartz crystal, ceramic resonator or external
clock
1: RC network
Bit 5 = Reserved, must be always cleared.
Section
Bit 4 = Reserved, must be always set.
98). It is there-
Bit 3 = NMI PULL NMI Pull-Up on/off.
This option bit enables or disables the internal pull-
up on the NMI pin.
0: Pull-up disabled
1: Pull-up enabled
Bit 2 = TIM PULL TIMER Pull-Up on/off.
This option bit enables or disables the internal pull-
up on the TIMER pin.
0: Pull-up disabled
1: Pull-up enabled
Bit 1 = WDACT Hardware or software watchdog.
This option bit selects the watchdog type.
0: Software (watchdog to be enabled by software)
1: Hardware (watchdog always enabled)
Bit 0 = OSGEN Oscillator Safeguard on/off.
This option bit enables or disables the oscillator
Safeguard (OSG) feature.
0: Oscillator Safeguard disabled
1: Oscillator Safeguard enabled
8
7
EXT
PRO-
LVD
OSC Res. Res.
CTL
TECT
X
X
X
X
X
LSB OPTION BYTE
NMI
TIM
PULL
PULL
X
X
X
X
X
0
WD
OSG
ACT
EN
X
X