IC MCU 8BIT OTP 4K 20 PDIP

ST62T20CB6

Manufacturer Part NumberST62T20CB6
DescriptionIC MCU 8BIT OTP 4K 20 PDIP
ManufacturerSTMicroelectronics
SeriesST6
ST62T20CB6 datasheet
 


Specifications of ST62T20CB6

Core ProcessorST6Core Size8-Bit
Speed8MHzPeripheralsLVD, POR, WDT
Number Of I /o12Program Memory Size4KB (4K x 8)
Program Memory TypeOTPRam Size64 x 8
Voltage - Supply (vcc/vdd)3 V ~ 6 VData ConvertersA/D 8x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case20-DIP (0.300", 7.62mm)Controller Family/seriesST6
No. Of I/o's12Ram Memory Size64Byte
Cpu Speed8MHzNo. Of Timers1
Rohs CompliantYesProcessor SeriesST62T2x
CoreST6Data Bus Width8 bit
Data Ram Size64 BMaximum Clock Frequency8 MHz
Number Of Programmable I/os12Number Of Timers2
Operating Supply Voltage3 V to 6 VMaximum Operating Temperature+ 85 C
Mounting StyleThrough HoleDevelopment Tools By SupplierST622XC-KIT/110, ST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
Minimum Operating Temperature- 40 COn-chip Adc8 bit
Lead Free Status / RoHS StatusLead free / RoHS CompliantEeprom Size-
Connectivity-Other names497-2098-5
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
Page 17/104

Download datasheet (2Mb)Embed
PrevNext
4 CENTRAL PROCESSING UNIT
4.1 INTRODUCTION
The CPU Core of ST6 devices is independent of the
I/O or Memory configuration. As such, it may be
thought of as an independent central processor
communicating with on-chip I/O, Memory and Pe-
ripherals via internal address, data, and control
buses.
4.2 MAIN FEATURES
40 basic instructions
9 main addressing modes
Two 8-bit index registers
Two 8-bit short direct registers
Low power modes
Maskable hardware interrupts
6-level hardware stack
4.3 CPU REGISTERS
The ST6 Family CPU core features six registers and
three pairs of flags available to the programmer.
These are described in the following paragraphs.
Accumulator (A). The accumulator is an 8-bit
general purpose register used in all arithmetic cal-
culations, logical operations, and data manipula-
Figure 7. CPU Registers
7
RESET VALUE = xxh
7
RESET VALUE = xxh
7
RESET VALUE = xxh
7
RESET VALUE = xxh
7
RESET VALUE = xxh
11
RESET VALUE = RESET VECTOR @ 0FFEh-0FFFh
ST6208C/ST6209C/ST6210C/ST6220C
tions. The accumulator can be addressed in Data
Space as a RAM location at address FFh. Thus
the ST6 can manipulate the accumulator just like
any other register in Data Space.
Index Registers (X, Y). These two registers are
used in Indirect addressing mode as pointers to
memory locations in Data Space. They can also
be accessed in Direct, Short Direct, or Bit Direct
addressing modes. They are mapped in Data
Space at addresses 80h (X) and 81h (Y) and can
be accessed like any other memory location.
Short Direct Registers (V, W). These two regis-
ters are used in Short Direct addressing mode.
This means that the data stored in V or W can be
accessed with a one-byte instruction (four CPU cy-
cles). V and W can also be accessed using Direct
and Bit Direct addressing modes. They are
mapped in Data Space at addresses 82h (V) and
83h (W) and can be accessed like any other mem-
ory location.
Note: The X and Y registers can also be used as
Short Direct registers in the same way as V and W.
Program Counter (PC). The program counter is a
12-bit register which contains the address of the
next instruction to be executed by the core. This
ROM location may be an opcode, an operand, or
the address of an operand.
0
ACCUMULATOR
0
X INDEX REGISTER
0
Y INDEX REGISTER
0
V SHORT INDIRECT
REGISTER
0
W SHORT INDIRECT
REGISTER
0
PROGRAM COUNTER
SIX LEVEL
STACK
CN
NORMAL FLAGS
CI
INTERRUPT FLAGS
CNMI ZNMI
NMI FLAGS
x = Undefined value
17/104
ZN
ZI
1