STM32F101C4T6A STMicroelectronics, STM32F101C4T6A Datasheet - Page 65

• Manufacturer Part Number: STM32F101C4T6A
• Description: MCU ARM 32BIT 16K FLASH 48-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101C4T6A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: STM32F101x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 10 Channel
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8313

STM32F101x4, STM32F101x6
Equation 1: R
The formula above
error below 1/4 of LSB. Here N = 12 (from 12-bit resolution).
Table 43.
1. Guaranteed by design, not tested in production.
Table 44.
1. ADC DC accuracy values are measured after internal calibration.
2. ADC Accuracy vs. Negative Injection Current: Injecting negative current on any of the standard (non-
3. Based on characterization, not tested in production.
1.5
7.5
13.5
28.5
41.5
55.5
71.5
239.5
Symbol
R
robust) analog input pins should be avoided as this significantly reduces the accuracy of the conversion
being performed on another analog input. It is recommended to add a Schottky diode (pin to ground) to
standard analog pins which may potentially inject negative current.
Any positive injection current within the limits specified for I
affect the ADC accuracy.
EO
EG
ED
ET
EL
AIN
<
------------------------------------------------------------- - R
f
T
ADC
Total unadjusted error
Offset error
Gain error
Differential linearity error
Integral linearity error
s
R
(cycles)
ADC accuracy - limited test conditions
×
AIN
AIN
C
(Equation
ADC
Parameter
max for f
max formula:
T
S
×
ln
(
1) is used to determine the maximum external impedance allowed for an
2
ADC
N
+
Doc ID 15058 Rev 5
0.11
0.54
0.96
2.04
2.96
3.96
5.11
17.1
2
)
= 14 MHz
–
f
f
V
T
Measurements made after
ADC calibration
ADC
PCLK2
ADC
A
DDA
= 25 °C
= 14 MHz, R
(1)
= 3 V to 3.6 V
t
S
= 28 MHz,
Test conditions
(µs)
INJ(PIN)
AIN
(1) (2)
and Σ I
< 10 kΩ,
INJ(PIN)
0.4
5.9
11.4
25.2
37.2
50
NA
NA
Electrical characteristics
in
±1.3
±0.5
±0.7
±0.8
Typ
±1
Section 5.3.12
R
AIN
max (kΩ)
Max
±1.5
±1.5
±1.5
±1
±2
(3)
does not
Unit
LSB
65/79