STM32F101ZET6 STMicroelectronics, STM32F101ZET6 Datasheet - Page 37

• Manufacturer Part Number: STM32F101ZET6
• Description: MCU ARM 512KB FLASH MEM 144-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101ZET6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 112
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: STM32F101x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 48 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 112
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• On-chip Dac: 12 bit, 2 Channel
• A/d Bit Size: 12 bit
• A/d Channels Available: 16
• Height: 1.4 mm
• Length: 20 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2 V
• Width: 20 mm
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-6439

STM32F101xC, STM32F101xD, STM32F101xE
Table 8.
1. All main power (V
2. I
3. Negative injection disturbs the analog performance of the device. See note in
4. When several inputs are submitted to a current injection, the maximum I
Table 9.
I
INJ(PIN)
I
supply, in the permitted range.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
characteristics.
positive and negative injected currents (instantaneous values). These results are based on
characterization with I
INJ(PIN)
Symbol
INJ(PIN)
Symbol
I
I
VDD
VSS
I
T
IO
STG
T
J
(2)(3)
must never be exceeded. This is implicitly insured if V
(2)
Current characteristics
Thermal characteristics
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRST pin
Injected current on High-speed external OSC_IN and Low-
speed external OSC_IN pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
, V
Storage temperature range
Maximum junction temperature
DDA
INJ(PIN)
IN
>V
) and ground (V
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Doc ID 14610 Rev 7
DD
SS
/V
Ratings
SS
DDA
ground lines (sink)
, V
Ratings
SSA
power lines (source)
) pins must always be connected to the external power
(4)
IN
maximum is respected. If V
(1)
(1)
INJ(PIN)
IN
<V
INJ(PIN)
(4)
Electrical characteristics
Section 5.3.17: 12-bit ADC
SS
–65 to +150
is the absolute sum of the
.
value. A positive
Value
150
Max.
 25
± 25
150
150
± 5
± 5
± 5
25
IN
maximum
Unit
Unit
37/106
°C
°C
mA