MC908QB8CDWE Freescale Semiconductor, MC908QB8CDWE Datasheet - Page 151

• Manufacturer Part Number: MC908QB8CDWE
• Description: IC MCU 8BIT 8K FLASH 16-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QB8CDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Processor Series: HC08QB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 14
• Number Of Timers: 4
• Operating Supply Voltage: 3 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: DEMO908QB8 - BOARD DEMO FOR MC68HC908QB8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

In wait mode, the CPU clocks are inactive. Refer to the wait mode subsection of each module to see if the
module is active or inactive in wait mode. Some modules can be programmed to be active in wait mode.
Wait mode can also be exited by a reset (or break in emulation mode). A break interrupt during wait mode
sets the SIM break stop/wait bit, SBSW, in the break status register (BSR). If the COP disable bit, COPD,
in the configuration register is 0, then the computer operating properly module (COP) is enabled and
remains active in wait mode.
Figure 14-15
14.7.2 Stop Mode
In stop mode, the SIM counter is reset and the system clocks are disabled. An interrupt request from a
module can cause an exit from stop mode. Stacking for interrupts begins after the selected stop recovery
time has elapsed. Reset or break also causes an exit from stop mode.
The SIM disables the oscillator signals (BUSCLKX2 and BUSCLKX4) in stop mode, stopping the CPU
and peripherals. If OSCENINSTOP is set, BUSCLKX4 will remain running in STOP and can be used to
run the AWU. Stop recovery time is selectable using the SSREC bit in the configuration register 1
(CONFIG1). If SSREC is set, stop recovery is reduced from the normal delay of 4096 BUSCLKX4 cycles
down to 32. This is ideal for the internal oscillator, RC oscillator, and external oscillator options which do
not require long start-up times from stop mode.
Freescale Semiconductor
and
EXITSTOPWAIT
NOTE: EXITSTOPWAIT = RST pin OR CPU interrupt
ADDRESS BUS
ADDRESS BUS
1. RST is only available if the RSTEN bit in the CONFIG2 register is set.
External crystal applications should use the full stop recovery time by
clearing the SSREC bit.
BUSCLKX4
DATA BUS
DATA BUS
Figure 14-16
RST
(1)
Figure 14-16. Wait Recovery from Internal Reset
$A6
$A6
Figure 14-15. Wait Recovery from Interrupt
show the timing for wait recovery.
$6E0B
$A6
$6E0B
$A6
MC68HC908QB8 Data Sheet, Rev. 3
$A6
$A6
CYCLES
$6E0C
32
NOTE
$01
$00FF
CYCLES
$0B
32
$00FE
$6E
RST VCT H
$00FD
RST VCT L
$00FC
Low-Power Modes
151