C8051F046-GQ Silicon Laboratories Inc, C8051F046-GQ Datasheet - Page 166

• Manufacturer Part Number: C8051F046-GQ
• Description: IC 8051 MCU 32K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F046-GQ

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: CAN, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F040DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• On-chip Dac: 12 bit, 2 Channel
• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F04x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1211

C8051F040/1/2/3/4/5/6/7
13.1. Power-On Reset
The C8051F04x family incorporates a power supply monitor that holds the MCU in the reset state until V
rises above the V
the Electrical Characteristics of the power supply monitor circuit. The /RST pin is asserted low until the end
of the 100 ms V
enabled and disabled using the external V
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. All of the other
reset flags in the RSTSRC register are indeterminate. PORSF is cleared by all other resets. Since all
resets cause program execution to begin at the same location (0x0000), software can read the PORSF
flag to determine if a power-up was the cause of reset. The contents of internal data memory should be
assumed to be undefined after a power-on reset.
13.2. Power-Fail Reset
When a power-down transition or power irregularity causes V
monitor will drive the /RST pin low and return the CIP-51 to the reset state. When V
above V
Figure 13.2). Note that even though internal data memory contents are not altered by the power-fail reset,
it is impossible to determine if V
set to logic 1, the data may no longer be valid.
13.3. External Reset
The external /RST pin provides a means for external circuitry to force the MCU into a reset state. Asserting
the /RST pin low will cause the MCU to enter the reset state. It may be desirable to provide an external pul-
166
Logic HIGH
Logic LOW
RST
, the CIP-51 will leave the reset state in the same manner as that for the power-on reset (see
2.70
2.55
2.0
1.0
DD
RST
Monitor timeout in order to allow the V
/RST
level during power-up. See Figure 13.2 for timing diagram, and refer to Table 13.1 for
V
RST
DD
dropped below the level required for data retention. If the PORSF flag is
Figure 13.2. Reset Timing
Power-On Reset
DD
Reset Time
Delay
monitor enable pin (MONEN).
Rev. 1.5
DD
supply to stabilize. The V
DD
to drop below V
VDD Monitor Reset
Reset Time
Delay
RST
DD
, the power supply
DD
returns to a level
Monitor reset is
t
DD