C8051F046-GQ Silicon Laboratories Inc, C8051F046-GQ Datasheet - Page 299

• Manufacturer Part Number: C8051F046-GQ
• Description: IC 8051 MCU 32K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F046-GQ

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: CAN, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F040DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• On-chip Dac: 12 bit, 2 Channel
• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F04x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1211

23.2.3. Auto-Reload Mode
In Auto-Reload Mode, the counter/timer can be configured to count up or down and cause an interrupt/flag
to occur upon an overflow/underflow event. When counting up, the counter/timer will set its overflow/under-
flow flag (TFn) and cause an interrupt (if enabled) upon overflow/underflow, the values in the Reload/Cap-
ture Registers (RCAPnH and RCAPnL) are loaded into the timer, and the timer is restarted. When the
Timer External Enable Bit (EXENn) bit is set to ‘1’ and the Decrement Enable Bit (DCEN) is ‘0’, a ‘1’-to-‘0’
transition on the TnEX pin (configured as an input in the digital crossbar) will cause a timer reload (in addi-
tion to timer overflows causing auto-reloads). When DCEN is set to ‘1’, the state of the TnEX pin controls
whether the counter/timer counts up (increments) or down (decrements), and will not cause an auto-reload
or interrupt event. See
When counting down, the counter/timer will set its overflow/underflow flag (TFn) and cause an interrupt (if
enabled) when the value in the timer (TMRnH and TMRnL registers) matches the 16-bit value in the
Reload/Capture Registers (RCAPnH and RCAPnL). This is considered an underflow event, and will cause
the timer to load the value 0xFFFF. The timer is automatically restarted when an underflow occurs.
Counter/Timer with Auto-Reload mode is selected by clearing the CP/RLn bit. Setting TRn to logic 1
enables and starts the timer.
In Auto-Reload Mode, the External Flag (EXFn) toggles upon every overflow or underflow and does not
cause an interrupt. The EXFn flag can be thought of as the most significant bit (MSB) of a 17-bit counter.
External Clock
SYSCLK
(XTAL1)
Tn
Figure 23.5. Tn Auto-reload Mode and Toggle Mode Block Diagram
TnE
X
Crossbar
8
2
12
Crossbar
Section 23.2.1
EXENn
TRn
0
1
for information concerning configuration of a timer to count down.
TMRnCF
M
T
n
1
M
T
n
0
T
O
G
n
Reload
O
T
n
E
Rev. 1.5
TCLK
D
E
C
E
N
RCAPnL
C8051F040/1/2/3/4/5/6/7
TMRnL
0xFF
RCAPnH
TMRnH
0xFF
Toggle Logic
OVF
CP/RLn
EXENn
EXFn
C/Tn
TRn
TFn
0
1
Interrupt
(Port Pin)
Tn
297