C8051F046-GQ Silicon Laboratories Inc, C8051F046-GQ Datasheet - Page 324

• Manufacturer Part Number: C8051F046-GQ
• Description: IC 8051 MCU 32K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F046-GQ

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: CAN, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F040DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• On-chip Dac: 12 bit, 2 Channel
• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F04x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1211

C8051F040/1/2/3/4/5/6/7
322
This register determines how the Flash interface logic will respond to reads and writes to the 
Bit 7:
Bits6-4:
Bits3-0:
SFLE
Bit7
JTAG Register Definition 25.3. FLASHCON: JTAG Flash Control Register
FLASHDAT Register. 
SFLE: Scratchpad Flash Memory Access Enable
When this bit is set, Flash reads and writes from user software are directed to the 128-byte
scratchpad Flash sector. When accessing the scratchpad, Flash accesses out of the
address range 0x00-0x7F should not be attempted. Reads/Writes outside of this range will
yield undefined results.
0: Flash access is directed to the Program/Data Flash sector.
1: Flash access is directed to the 128-byte scratchpad sector.
WRMD2-0: Write Mode Select Bits.
The Write Mode Select Bits control how the interface logic responds to writes to the FLASH-
DAT Register per the following values:
000:
001:
010:
(All other values for WRMD2-0 are reserved.)
RDMD3-0: Read Mode Select Bits.
The Read Mode Select Bits control how the interface logic responds to reads to the FLASH-
DAT Register per the following values:
0000:
0001:
0010:
(All other values for RDMD3-0 are reserved.)
WRMD2
Bit6
A FLASHDAT write replaces the data in the FLASHDAT register, but is otherwise
ignored.
A FLASHDAT write initiates a write of FLASHDAT into the memory address by the
FLASHADR register. FLASHADR is incremented by one when complete.
A FLASHDAT write initiates an erasure (sets all bytes to 0xFF) of the Flash page
containing the address in FLASHADR. The data written must be 0xA5 for the erase
to occur. FLASHADR is not affected. If FLASHADR targets the Read Lock Byte or
the Write/Erase Lock Byte, the entire user space will be erased (i.e. entire Flash
memory except for the Reserved area (See
page
A FLASHDAT read provides the data in the FLASHDAT register, but is otherwise
ignored.
A FLASHDAT read initiates a read of the byte addressed by the FLASHADR regis-
ter if no operation is currently active. This mode is used for block reads.
A FLASHDAT read initiates a read of the byte addressed by FLASHADR only if no
operation is active and any data from a previous read has already been read from
FLASHDAT. This mode allows single bytes to be read (or the last byte of a block)
without initiating an extra read.
WRMD1
179).
Bit5
WRMD0
Bit4
RDMD3
Rev. 1.5
Bit3
RDMD2
Bit2
Section “15. Flash Memory” on
RDMD1
Bit1
RDMD0
Bit0
00000000
Reset Value