M30626FJPFP#U5C Renesas Electronics America, M30626FJPFP#U5C Datasheet - Page 182

IC M16C MCU FLASH 512K 100QFP

M30626FJPFP#U5C

Manufacturer Part Number
M30626FJPFP#U5C
Description
IC M16C MCU FLASH 512K 100QFP
Manufacturer
Renesas Electronics America
Series
M16C™ M16C/60r
Datasheets

Specifications of M30626FJPFP#U5C

Core Processor
M16C/60
Core Size
16-Bit
Speed
24MHz
Connectivity
I²C, IEBus, UART/USART
Peripherals
DMA, WDT
Number Of I /o
85
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Ram Size
31K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 26x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 85°C
Package / Case
100-QFP
For Use With
867-1000 - KIT QUICK START RENESAS 62PR0K33062PS001BE - R0K33062P STARTER KITR0K33062PS000BE - KIT EVAL STARTER FOR M16C/62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M30626FJPFP#U5CM30626FJPFP
Manufacturer:
RENESAS
Quantity:
2
Company:
Part Number:
M30626FJPFP#U5CM30626FJPFP
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
M30626FJPFP#U5CM30626FJPFP#U3C
Manufacturer:
MIT
Quantity:
1 831
Company:
Part Number:
M30626FJPFP#U5CM30626FJPFP#U3C
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
M30626FJPFP#U5C
Manufacturer:
ST
Quantity:
1 001
M16C/62P Group (M16C/62P, M16C/62PT)
Rev.2.41
REJ09B0185-0241
16. Three-Phase Motor Control Timer Function
Timers A1, A2, A4 and B2 can be used to output three-phase motor drive waveforms. Table 16.1 lists the Three-phase
Motor Control Timer Functions Specifications. Figure 16.1 shows the Three-phase Motor Control Timer Functions
Block Diagram. Also, the related registers are shown on Figure 16.2 to Figure 16.8.
Table 16.1
NOTES:
Three-Phase Waveform Output Pin
Forced Cutoff Input
Used Timers
Output Waveform
Carrier Wave Cycle
Three-Phase PWM Output Width
Dead Time
Active Level
Positive and Negative-Phase
Concurrent Active Disable Function
Interrupt Frequency
1. Forced cutoff with NMI input is effective when the IVPCR1 bit in the TB2SC register is set to “1”
The M16C/62P (80-pin version) and M16C/62PT (80-pin version) do not use this function.
Note
(three-phase output forcible cutoff by NMI input enabled). If an “L” signal is applied to the NMI pin
when the IVPCR1 bit is “1,” the related pins go to a high-impedance state regardless of which
functions of those pins are being used.
Related pins
Jan 10, 2006
Three-phase Motor Control Timer Functions Specifications
Item
(1)
P7_2/CLK2/TA1OUT/V, P7_3/CTS2/RTS2/TA1IN/V, P7_4/TA2OUT/W,
P7_5/TA2IN/W, P8_0/TA4OUT/U, P8_1/TA4IN/U
Page 165 of 390
Six pins (U, U, V, V, W, W)
Input “L” to NMI pin
Timer A4, A1, A2 (used in the one-shot timer mode)
Timer B2 (used in the timer mode)
Dead time timer (3 eight-bit timer and shared reload register)
Triangular wave modulation, Sawtooth wave modification
Triangular wave modulation: count source x (m+1) x 2
Sawtooth wave modulation: count source x (m+1)
Triangular wave modulation: count source x n x 2
Sawtooth wave modulation: count source x n
Count source: f1, f2, f8, f32, fC32
Count source x p, or no dead time
Count source: f1, f2, f1 divided by 2, f2 divided by 2
Enable to select “H” or “L”
Positive and negative-phases concurrent active disable function
Positive and negative-phases concurrent active detect function
For Timer B2 interrupt, select a carrier wave cycle-to-cycle basis
through 15 times carrier wave cycle-to-cycle basis
Timer A4: U- and U-phase waveform control
Timer A1: V- and V-phase waveform control
Timer A2: W- and W-phase waveform control
Carrier wave cycle control
Dead time control
Enable to output “H” or “L” for one cycle
Enable to set positive-phase level and negative-phase level
respectively
m: Setting value of TB2 register, 0000h to FFFFh
Count source: f1, f2, f8, f32, fC32
n: Setting value of TA4, TA1 and TA2 register (of TA4, TA41,
TA1, TA11, TA2 and TA21 registers when setting the INV11 bit
to “1”), 0001h to FFFFh
p: Setting value of DTT register, 01h to FFh
16. Three-Phase Motor Control Timer Function
Specification

Related parts for M30626FJPFP#U5C