M30626FJPGP#U3C Renesas Electronics America, M30626FJPGP#U3C Datasheet - Page 163

IC M16C MCU FLASH 512K 100LQFP

M30626FJPGP#U3C

Manufacturer Part Number
M30626FJPGP#U3C
Description
IC M16C MCU FLASH 512K 100LQFP
Manufacturer
Renesas Electronics America
Series
M16C™ M16C/60r
Datasheets

Specifications of M30626FJPGP#U3C

Core Processor
M16C/60
Core Size
16-Bit
Speed
24MHz
Connectivity
I²C, IEBus, UART/USART
Peripherals
DMA, WDT
Number Of I /o
85
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Ram Size
31K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 26x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-LQFP
For Use With
867-1000 - KIT QUICK START RENESAS 62PR0K33062PS001BE - R0K33062P STARTER KITR0K33062PS000BE - KIT EVAL STARTER FOR M16C/62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M30626FJPGP#U3CM30626FJPGP
Manufacturer:
ATMEL
Quantity:
1
Company:
Part Number:
M30626FJPGP#U3CM30626FJPGP
Manufacturer:
MIT
Quantity:
1 000
Company:
Part Number:
M30626FJPGP#U3CM30626FJPGP
Manufacturer:
MIT
Quantity:
20 000
Company:
Part Number:
M30626FJPGP#U3CM30626FJPGP
Manufacturer:
RENESAS
Quantity:
9 423
Company:
Part Number:
M30626FJPGP#U3CM30626FJPGP U5C
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
M16C/62P Group (M16C/62P, M16C/62PT)
Rev.2.41
REJ09B0185-0241
15.1.2
Table 15.2
Count Source
Count Operation
Divided Ratio
Count Start Condition
Count Stop Condition
Interrupt Request
Generation Timing
TAiIN Pin Function
TAiOUT Pin Function
Read from Timer
Write to Timer
Select Function
In event counter mode, the timer counts pulses from an external device or overflows and underflows of other
timers. Timer A2, A3 and A4 can count two-phase external signals. Table 15.2 lists Specifications in Event Counter
Mode (when not processing two-phase pulse signal). Table 15.3 lists Specifications in Event Counter Mode (when
processing two-phase pulse signal with Timer A2, A3 and A4). Figure 15.9 shows TAiMR Register in Event
Counter Mode (when not using two-phase pulse signal processing). Figure 15.10 shows TA2MR to TA4MR
Registers in Event Counter Mode (when using two-phase pulse signal processing with Timer A2, A3 and A4).
Jan 10, 2006
Item
Event Counter Mode
Specifications in Event Counter Mode (when not processing two-phase pulse signal)
Page 146 of 390
• External signals input to TAiIN pin (i=0 to 4) (effective edge can be selected in
• Timer B2 overflows or underflows,
• Up-count or down-count can be selected by external signal or program
• When the timer overflows or underflows, it reloads the reload register contents
1/ (FFFFh - n + 1) for up-count
1/ (n + 1) for down-count n : set value of TAi register 0000h to FFFFh
Set TAiS bit in the TABSR register to “1” (= start counting)
Set TAiS bit to “0” (= stop counting)
Timer overflow or underflow
I/O port or count source input
I/O port, pulse output, or up/down-count select input
Count value can be read by reading TAi register
• When not counting and until the 1st count source is input after counting start
• When counting (after 1st count source input)
• Free-run count function
• Pulse output function
program)
and continues counting. When operating in free-running mode, the timer
continues counting without reloading.
Timer Aj (j=i-1, except j=4 if i=0) overflows or underflows,
Timer Ak (k=i+1, except k=0 if i=4) overflows or underflows
Value written to TAi register is written to both reload register and counter
Value written to TAi register is written to only reload register
(Transferred to counter when reloaded next)
Even when the timer overflows or underflows, the reload register content is
not reloaded to it
Whenever the timer underflows or underflows, the output polarity of TAiOUT
pin is inverted. When TAiS bit is set to “0” (stop counting), the pin outputs a
low.
Specification
15. Timers

Related parts for M30626FJPGP#U3C