PIC24HJ256GP610-I/PT Microchip Technology, PIC24HJ256GP610-I/PT Datasheet - Page 40

• Manufacturer Part Number: PIC24HJ256GP610-I/PT
• Description: IC PIC MCU FLASH 128KX16 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ256GP610-I/PT

• Core Size: 16-Bit
• Program Memory Size: 256KB (85.5K x 24)
• Core Processor: PIC
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b, 32x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 85
• Ram Memory Size: 16KB
• Cpu Speed: 40MIPS
• No. Of Timers: 13
• No. Of Pwm Channels: 8
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: CAN, I2C, SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 13
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (12 bit, 32 Channel)
• A/d Bit Size: 12 bit
• A/d Channels Available: 32
• Height: 1 mm
• Length: 12 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Width: 12 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDAC164333 - MODULE SKT FOR PM3 100QFPDM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

TABLE 5-5:
FIGURE 5-8:
DS70152H-page 40
Step 8: Wait for Row Program operation to complete and make sure WR bit is clear.
Step 9: Repeat steps 3-8 until all code memory is programmed.
Command
(Binary)
0000
0000
0000
0001
0000
0000
—
—
SERIAL INSTRUCTION EXECUTION FOR WRITING CODE MEMORY (CONTINUED)
803B00
883C20
000000
<VISI>
040200
000000
(Hex)
PROGRAM CODE MEMORY FLOW
Data
—
—
LoopCount + 1
LoopCount =
N = 1
Externally time ‘P13’ msec (see
Timing
complete.
MOV
MOV
NOP
Clock out contents of VISI register.
GOTO
NOP
Repeat until the WR bit is clear.
Requirements”) to allow sufficient time for the Row Program operation to
NVMCON, W0
W0, VISI
0x200
N = N + 1
No
No
Start Write Sequence
and Poll for WR bit
Buffer at <Addr>
Load 2 Bytes
to be cleared
Section 8.0 “AC/DC Characteristics and
Device for
Configure
locations
to Write
written?
Description
Writes
done?
bytes
Start
End
All
All
Yes
Yes
N = 1
LoopCount = 0
© 2010 Microchip Technology Inc.