ATMEGA48V-10MMU Atmel, ATMEGA48V-10MMU Datasheet - Page 46

• Manufacturer Part Number: ATMEGA48V-10MMU
• Description: MCU AVR 4K FLASH 10MHZ 28-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA48V-10MMU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Processor Series: ATMEGA48x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire, SPI, USART, Serial
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 28MLF EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 10 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVR
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.4
10.5
46
External Reset
Brown-out Detection
ATmega48/88/168
Figure 10-3. MCU Start-up, RESET Extended Externally
An External Reset is generated by a low level on the RESET pin. Reset pulses longer than the
minimum pulse width (see
reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset.
When the applied signal reaches the Reset Threshold Voltage – V
delay counter starts the MCU after the Time-out period – t
can be disabled by the RSTDISBL fuse, see
Figure 10-4. External Reset During Operation
ATmega48/88/168 has an On-chip Brown-out Detection (BOD) circuit for monitoring the V
level during operation by comparing it to a fixed trigger level. The trigger level for the BOD can
be selected by the BODLEVEL Fuses. The trigger level has a hysteresis to ensure spike free
Brown-out Detection. The hysteresis on the detection level should be interpreted as V
V
value below the trigger level (V
vated. When V
starts the MCU after the Time-out period t
The BOD circuit will only detect a drop in V
ger than t
BOT
INTERNAL
TIME-OUT
+ V
RESET
RESET
HYST
BOD
V
CC
CC
/2 and V
given in
CC
increases above the trigger level (V
BOT-
“System and Reset Characteristics” on page
= V
V
“System and Reset Characteristics” on page
POT
BOT
BOT-
- V
HYST
in
Figure
/2.When the BOD is enabled, and V
TOUT
CC
Table 27-6 on page
if the voltage stays below the trigger level for lon-
has expired.
10-5), the Brown-out Reset is immediately acti-
V
RST
t
TOUT
BOT+
TOUT
in
– has expired. The External Reset
Figure
286.
RST
306.
– on its positive edge, the
10-5), the delay counter
306) will generate a
CC
decreases to a
2545S–AVR–07/10
BOT+
CC
=