PIC18LF2410T-I/SO Microchip Technology, PIC18LF2410T-I/SO Datasheet

IC MCU FLASH 8KX16 28SOIC

PIC18LF2410T-I/SO

Manufacturer Part Number
PIC18LF2410T-I/SO
Description
IC MCU FLASH 8KX16 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 18Fr

Specifications of PIC18LF2410T-I/SO

Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
25
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
The PIC18F2410/2510/4410/4510 Rev. A1 parts you
have received conform functionally to the Device Data
Sheet
described below. Any Data Sheet Clarification issues
related to the PIC18F2410/2510/4410/4510 will be
reported in a separate Data Sheet errata. Please check
the Microchip web site for any existing issues.
The
PIC18F2410/2510/4410/4510 devices with these
Device/Revision IDs:
TABLE 1:
© 2007 Microchip Technology Inc.
The Device IDs (DEVID1 and DEVID2) are located at
addresses
configuration space. They are shown in binary in the
format “DEVID2 DEVID1”.
Note 1:
Part Number
PIC18F2410
PIC18F2510
PIC18F4410
PIC18F4510
following
40 MHz
40 MHz
40 MHz
16 MHz
16 MHz
16 MHz
(DS39636C),
4 MHz
4 MHz
4 MHz
F
OSC
The I
100 kHz) in all details, but may be used with care where higher rates are required by the application.
PIC18F2410/2510/4410/4510 Rev. A1 Silicon Errata
3FFFFEh:3FFFFFh
I
2
2
C™ interface does not conform to the 400 kHz I
C™ CLOCK RATE w/BRG
silicon
0001 0001 011
0001 0001 001
0001 0000 101
0001 0000 111
Device ID
except
errata apply
10 MHz
10 MHz
10 MHz
4 MHz
4 MHz
4 MHz
1 MHz
1 MHz
1 MHz
for
F
CY
in
the
PIC18F2410/2510/4410/4510
Revision ID
the
0 0100
0 0100
0 0100
0 0100
anomalies
only
device’s
to
20 MHz
20 MHz
20 MHz
F
8 MHz
8 MHz
8 MHz
2 MHz
2 MHz
2 MHz
CY
* 2
1. Module: MSSP
2
C specification (which applies to rates greater than
SSPADD = INT((F
In its current implementation, the I
mode operates as follows:
a)
b)
Date Codes that pertain to this issue:
All engineering and production devices.
The Baud Rate Generator for I
mode is slower than the rates specified in
Table 16-3 of the Device Data Sheet.
For this revision of silicon, use the values
shown in Table 1 in place of those shown in
Table 16-3 of the Device Data Sheet. The
differences are shown in bold text.
Use the following formula in place of the
one shown in Register 16-2 (SSPCON1) of
the Device Data Sheet for bit description
SSPM3:SSPM0 = 1000.
BRG Value
0Eh
15h
59h
05h
08h
23h
01h
08h
00h
CY
/F
SCL
) – (F
(2 Rollovers of BRG)
CY
/1.111 MHz)) – 1
400 kHz
400 kHz
333 kHz
312.5 kHz
DS80277C-page 1
1 MHz
100 kHz
308 kHz
100 kHz
100 kHz
2
F
C in Master
2
SCL
C™ Master
(1)
(1)
(1)
(1)

Related parts for PIC18LF2410T-I/SO

PIC18LF2410T-I/SO Summary of contents

Page 1

... Note 1: The I C™ interface does not conform to the 400 kHz I 100 kHz) in all details, but may be used with care where higher rates are required by the application. © 2007 Microchip Technology Inc. PIC18F2410/2510/4410/4510 1. Module: MSSP In its current implementation, the I the anomalies ...

Page 2

... Configure the auto-shutdown for software restart by clearing the PRSEN bit (PWM1CON<7>). The PWM can be re-enabled by clearing the ECCPASE bit (ECCP1AS<7>) after the shutdown condition expires. Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc. ...

Page 3

... Work around None. Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc. PIC18F2410/2510/4410/4510 8. Module: ECCP and CCP The CCP1 and CCP2 configured for PWM mode, with 1:1 Timer2 prescaler and duty cycle set to the period minus 1, may result in the PWM output(s) remaining at a logic low level ...

Page 4

... Disable the auto-restart feature in software, polling the Timer2 Interrupt Flag, TMR2IF, and wait until it is set before clearing the ECCPASE bit. Date Codes that pertain to this issue: All engineering and production devices. Trigger (CCP1CON bits, TMRxH:TMRxL and In other words, if © 2007 Microchip Technology Inc. ...

Page 5

... TMRT is set and prior to writing subsequent bytes into TXREG. Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc. PIC18F2410/2510/4410/4510 17. Module: Timer1/Timer3 When Timer1 or Timer3 is configured for the external clock source and the CCPxCON register ...

Page 6

... Example 2 can be used. This example overwrites the Fast Return register by making a dummy call to Foo with the fast option in the high priority service routine. Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc. ...

Page 7

... Microchip Technology Inc. PIC18F2410/2510/4410/4510 directive instructs the compiler to not use the RETFIE FAST instruction. If the proper high priority interrupt bit is set in the IPRx register, then the interrupt is treated as high priority in spite of the pragma interruptlow directive. ...

Page 8

... EUSART transmits a shorter than expected clock on the CK pin for bit 0. Work around None. Date Codes that pertain to this issue: All engineering and production devices. Units Conditions LSb and V - REF REF REF LSb and V REF SS DD © 2007 Microchip Technology Inc. ...

Page 9

... C slave must clear the SSPOV bit after each event to maintain normal operation. Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc. PIC18F2410/2510/4410/4510 28. Module: MSSP Master mode, the BRG value of ‘0’ may not work correctly. ...

Page 10

... MOVWF RXDATA ;Save in user RAM MOVF TXDATA TXDATA BCF T2CON, TMR2ON ;Timer2 off CLRF TMR2 ;Clear Timer2 MOVWF SSPBUF ;Xmit New data BSF T2CON, TMR2ON ;Timer2 on Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc ...

Page 11

... TXREG. Do not load the TXREG when the timer is about to overflow. Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc. PIC18F2410/2510/4410/4510 34. Module: EUSART In 9-Bit Asynchronous Full-Duplex Receive mode, the received data may be corrupted if the TX9D bit (TXSTA< ...

Page 12

... While keeping the LAT bits clear, configure SCL and SDA as inputs by setting their TRIS bits. Once this is done, use the SSPCON1 and SSPCON2 registers to configure the proper I mode as before. Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc operation ...

Page 13

... Q4 cycle). Work around None Date Codes that pertain to this issue: All engineering and production devices. © 2007 Microchip Technology Inc. PIC18F2410/2510/4410/4510 43. Module: 10-Bit Analog-to-Digital (A/D) Converter When the A/D clock source is selected (when ADCS2:ADCS0 = 000 or x11), in ...

Page 14

... Timer3), 20 (Interrupts), 21 (A/D), 22 (BOR), 23-26 (EUSART), 27-31 (MSSP), 32 (MSSP – SPI Mode), 33- 36 (EUSART), 37 (Timer1), 38-41 (MSSP) and 42 (Reset). Rev B Document (10/2006) Corrected Device IDs. Rev C Document (8/2007) Added silicon issue 43 (10-Bit A/D Converter). DS80277C-page 14 © 2007 Microchip Technology Inc. ...

Page 15

... PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...

Page 16

... Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2007 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...

Related keywords