PIC18LF2410T-I/SO Microchip Technology, PIC18LF2410T-I/SO Datasheet - Page 208

• Manufacturer Part Number: PIC18LF2410T-I/SO
• Description: IC MCU FLASH 8KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF2410T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

PIC18F2X1X/4X1X
17.3.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA<5>), or the Continuous Receive
Enable bit, CREN (RCSTA<4>). Data is sampled on the
RX pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
To set up a Synchronous Master Reception:
1.
2.
FIGURE 17-13:
TABLE 17-8:
DS39636D-page 210
INTCON
PIR1
PIE1
IPR1
RCSTA
RCREG
TXSTA
BAUDCON
SPBRGH
SPBRG
Legend:
Note 1:
Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
Name
RC7/TX/CK pin
RC7/TX/CK pin
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRG16
bit, as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
RC7/RX/DT
(SCKP = 0)
(SCKP = 1)
(Interrupt)
CREN bit
bit SREN
SREN bit
RCIF bit
RXREG
Write to
— = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
These bits are unimplemented on 28-pin devices and read as ‘0’.
EUSART SYNCHRONOUS
MASTER RECEPTION
Read
EUSART Receive Register
EUSART Baud Rate Generator Register, High Byte
EUSART Baud Rate Generator Register, Low Byte
GIE/GIEH
ABDOVF
PSPIE
PSPIP
PSPIF
pin
SPEN
CSRC
Q2
Bit 7
‘0’
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
(1)
(1)
(1)
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
PEIE/GIEL
RCIDL
ADIF
ADIE
ADIP
Bit 6
RX9
TX9
bit 0
TMR0IE
SREN
TXEN
RCIF
RCIE
RCIP
Bit 5
—
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 1
INT0IE
CREN
SYNC
SCKP
bit 2
Bit 4
TXIF
TXIE
TXIP
bit 3
ADDEN
SENDB
BRG16
SSPIF
SSPIE
SSPIP
RBIE
Bit 3
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE
Ensure bits CREN and SREN are clear.
If interrupts are desired, set enable bit RCIE.
If 9-bit reception is desired, set bit RX9.
If a single reception is required, set bit SREN.
For continuous reception, set bit CREN.
Interrupt flag bit RCIF will be set when reception
is complete and an interrupt will be generated if
the enable bit RCIE was set.
Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
bit CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
bit 4
TMR0IF
CCP1IE
CCP1IP
CCP1IF
BRGH
FERR
Bit 2
—
bit 5
TMR2IF
TMR2IE
TMR2IP
INT0IF
OERR
TRMT
WUE
Bit 1
© 2009 Microchip Technology Inc.
bit 6
TMR1IF
TMR1IE
TMR1IP
ABDEN
RX9D
TX9D
bit 7
RBIF
Bit 0
Q1 Q2 Q3 Q4
Values on
Reset
page
51
54
54
54
53
53
53
53
53
53
‘0’