PIC18LF2410T-I/SO Microchip Technology, PIC18LF2410T-I/SO Datasheet - Page 231

IC MCU FLASH 8KX16 28SOIC

PIC18LF2410T-I/SO

Manufacturer Part Number
PIC18LF2410T-I/SO
Description
IC MCU FLASH 8KX16 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 18Fr

Specifications of PIC18LF2410T-I/SO

Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
25
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
21.0
PIC18F2X1X/4X1X devices have a High/Low-Voltage
Detect module (HLVD). This is a programmable circuit
that allows the user to specify both a device voltage trip
point and the direction of change from that point. If the
device experiences an excursion past the trip point in
that direction, an interrupt flag is set. If the interrupt is
enabled, the program execution will branch to the inter-
rupt vector address and the software can then respond
to the interrupt.
REGISTER 21-1:
© 2009 Microchip Technology Inc.
HIGH/LOW-VOLTAGE DETECT
(HLVD)
bit 7
bit 6
bit 5
bit 4
bit 3-0
HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER
bit 7
VDIRMAG: Voltage Direction Magnitude Select bit
1 = Event occurs when voltage equals or exceeds trip point (HLVDL3:HLDVL0)
0 = Event occurs when voltage equals or falls below trip point (HLVDL3:HLVDL0)
Unimplemented: Read as ‘0’
IRVST: Internal Reference Voltage Stable Flag bit
1 = Indicates that the voltage detect logic will generate the interrupt flag at the specified voltage
0 = Indicates that the voltage detect logic will not generate the interrupt flag at the specified
HLVDEN: High/Low-Voltage Detect Power Enable bit
1 = HLVD enabled
0 = HLVD disabled
HLVDL3:HLVDL0: Voltage Detection Limit bits
1111 = External analog input is used (input comes from the HLVDIN pin)
1110 = Maximum setting
.
.
.
0000 = Minimum setting
VDIRMAG
Legend:
R = Readable bit
-n = Value at POR
Note:
R/W-0
range
voltage range and the HLVD interrupt should not be enabled
See Table 25-4 in Section 25.0 “Electrical Characteristics” for the specifications.
U-0
IRVST
R-0
W = Writable bit
‘1’ = Bit is set
HLVDEN
R/W-0
The
(Register 21-1) completely controls the operation of the
HLVD module. This allows the circuitry to be “turned
off” by the user under software control, which
minimizes the current consumption for the device.
The block diagram for the HLVD module is shown in
Figure 21-1.
PIC18F2X1X/4X1X
High/Low-Voltage
HLVDL3
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
HLVDL2
R/W-1
Detect
HLVDL1
x = Bit is unknown
R/W-0
DS39636D-page 233
Control
HLVDL0
R/W-1
register
bit 0

Related parts for PIC18LF2410T-I/SO