PIC18LF2410T-I/SO Microchip Technology, PIC18LF2410T-I/SO Datasheet - Page 42

IC MCU FLASH 8KX16 28SOIC

PIC18LF2410T-I/SO

Manufacturer Part Number
PIC18LF2410T-I/SO
Description
IC MCU FLASH 8KX16 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 18Fr

Specifications of PIC18LF2410T-I/SO

Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
25
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
PIC18F2X1X/4X1X
REGISTER 4-1:
DS39636D-page 44
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
RCON: RESET CONTROL REGISTER
bit 7
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
SBOREN: BOR Software Enable bit
If BOREN1:BOREN0 = 01:
1 = BOR is enabled
0 = BOR is disabled
If BOREN1:BOREN0 = 00, 10 or 11:
Bit is disabled and read as ‘0’.
Unimplemented: Read as ‘0’
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware only)
0 = The RESET instruction was executed causing a device Reset (must be set in software after
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
POR: Power-on Reset Status bit
1 = A Power-on Reset has not occurred (set by firmware only)
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
Legend:
R = Readable bit
-n = Value at POR
R/W-0
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been
Note 1: The SBOREN bit is only available when the BOREN1:BOREN0 Configuration
IPEN
a Brown-out Reset occurs)
2: The actual Reset value of POR is determined by the type of device Reset. See the
2: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming
bits = 01; otherwise, it is disabled and reads as ‘0’. See Section 4.4 “Brown-out
Reset (BOR)”.
notes following this register and Section 4.6 “Reset State of Registers” for
additional information.
detected so that subsequent Power-on Resets may be detected.
that POR was set to ‘1’ by software immediately after POR).
SBOREN
R/W-1
(1)
U-0
W = Writable bit
‘1’ = Bit is set
(2)
(1)
R/W-1
RI
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-1
TO
R-1
PD
© 2009 Microchip Technology Inc.
x = Bit is unknown
R/W-0
POR
(2)
R/W-0
BOR
bit 0

Related parts for PIC18LF2410T-I/SO