ATMEGA32U4-AUR Atmel, ATMEGA32U4-AUR Datasheet - Page 90

MCU AVR 16K FLASH 16MHZ 44TQFP

ATMEGA32U4-AUR

Manufacturer Part Number
ATMEGA32U4-AUR
Description
MCU AVR 16K FLASH 16MHZ 44TQFP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet

Specifications of ATMEGA32U4-AUR

Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
26
Program Memory Size
32KB (16K x 16)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2.5K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 12x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
44-TQFP, 44-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA32U4-AUR
Manufacturer:
Atmel
Quantity:
10 000
12.4
7766F–AVR–11/10
General Timer/Counter Control Register – GTCCR
Each half period of the external clock applied must be longer than one system clock cycle to
ensure correct sampling. The external clock must be guaranteed to have less than half the sys-
tem clock frequency (f
sampling, the maximum frequency of an external clock it can detect is half the sampling fre-
quency (Nyquist sampling theorem). However, due to variation of the system clock frequency
and duty cycle caused by Oscillator source (crystal, resonator, and capacitors) tolerances, it is
recommended that maximum frequency of an external clock source is less than f
An external clock source can not be prescaled.
Figure 12-2. Prescaler for synchronous Timer/Counters
Note:
• Bit 7 – TSM: Timer/Counter Synchronization Mode
Writing the TSM bit to one activates the Timer/Counter Synchronization mode. In this mode, the
value that is written to the PSRASY and PSRSYNC bits is kept, hence keeping the correspond-
ing prescaler reset signals asserted. This ensures that the corresponding Timer/Counters are
halted and can be configured to the same value without the risk of one of them advancing during
configuration. When the TSM bit is written to zero, the PSRASY and PSRSYNC bits are cleared
by hardware, and the Timer/Counters start counting simultaneously.
• Bit 0 – PSRSYNC: Prescaler Reset for Synchronous Timer/Counters
When this bit is one, Timer/Counter0 and Timer/Counter1 and Timer/Counter3 prescaler will be
Reset. This bit is normally cleared immediately by hardware, except if the TSM bit is set. Note
that Timer/Counter0, Timer/Counter1 and Timer/Counter3 share the same prescaler and a reset
of this prescaler will affect all timers.
Bit
Read/Write
Initial Value
PSR10
clk
CSn0
CSn1
CSn2
Tn
Tn
I/O
T3 input is not available on the
either T0 or T1 inputs.
Synchronization
Synchronization
7
TSM
R/W
0
6
R
0
ExtClk
< f
TIMER/COUNTERn CLOCK SOURCE
clk_I/O
5
R
0
/2) given a 50/50% duty cycle. Since the edge detector uses
ATmega16U4/ATmega32U4 products. “Tn” only refers to
clk
Clear
Tn
4
R
0
3
R
0
CSn0
CSn1
CSn2
2
R
0
ATmega16/32U4
TIMER/COUNTERn CLOCK SOURCE
1
PSRASY
R/W
0
clk
Tn
0
PSRSYNC
R/W
0
clk_I/O
/2.5.
GTCCR
90

Related parts for ATMEGA32U4-AUR