ATMEGA32U4-MUR Atmel, ATMEGA32U4-MUR Datasheet - Page 32

no-image

ATMEGA32U4-MUR

Manufacturer Part Number
ATMEGA32U4-MUR
Description
MCU AVR 16K FLASH 16MHZ 44VQFN
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet

Specifications of ATMEGA32U4-MUR

Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
26
Program Memory Size
32KB (16K x 16)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2.5K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 12x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
44-VQFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA32U4-MUR
Manufacturer:
UCC
Quantity:
1 001
6.5
6.5.1
7766F–AVR–11/10
Calibrated Internal RC Oscillator
Oscillator Calibration Register – OSCCAL
Note:
The calibrated internal RC Oscillator by default provides a 8.0 MHz clock. This frequency is
nominal value at 3V and 25°C. The device is shipped with the CKDIV8 Fuse programmed. See
“System Clock Prescaler” on page 37
clock by programming the CKSEL Fuses as shown in
no external components. During reset, hardware loads the calibration byte into the OSCCAL
Register and thereby automatically calibrates the RC Oscillator. At 3V and 25°C, this calibration
gives a frequency of 8 MHz ± 1%. The oscillator can be calibrated to any frequency in the range
7.3 - 8.1 MHz within ±1% accuracy, by changing the OSCCAL register. When this Oscillator is
used as the chip clock, the Watchdog Oscillator will still be used for the Watchdog Timer and for
the Reset Time-out. For more information on the pre-programmed calibration value, see the sec-
tion
Table 6-7.
Notes:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table 6-5 on page
Table 6-8.
• Bits 7..0 – CAL7..0: Oscillator Calibration Value
The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to
remove process variations from the oscillator frequency. The factory-calibrated value is automat-
ically written to this register during chip reset, giving an oscillator frequency of 8.0 MHz at 25°C.
The application software can write this register to change the oscillator frequency. The calibra-
tion range is +/- 40% and linear (calibration step ~0.4%). With typical process at 25°C the code
should be 127 for 8 MHz. Input value of 0x00 gives the lowest frequency, and 0xFF the highest.
Bit
Read/Write
Initial Value
Power Conditions
BOD enabled
Fast rising power
Slowly rising power
“Calibration Byte” on page 349
1. These options should only be used if frequency stability at start-up is not important for the
1. The device is shipped with this option selected.
2. The frequency ranges are preliminary values. Actual values are TBD.
3. If 8 MHz frequency exceeds the specification of the device (depends on V
application.
Fuse can be programmed in order to divide the internal frequency by 8.
7
CAL7
R/W
Device Specific Calibration Value
Frequency Range
Internal Calibrated RC Oscillator Operating Modes
Start-up times for the internal calibrated RC Oscillator clock selection
31.
6
CAL6
R/W
7.3 - 8.1
Start-up Time from Power-
down and Power-save
5
CAL5
R/W
(2)
(MHz)
Reserved
6 CK
6 CK
6 CK
for more details. This clock may be selected as the system
4
CAL4
R/W
3
CAL3
R/W
2
CAL2
R/W
Table
Additional Delay from
Reset (V
14CK + 4.1 ms
14CK + 65 ms
6-7. If selected, it will operate with
14CK
1
CAL1
R/W
ATmega16/32U4
CC
(1)(3)
CKSEL[3:0]
= 5.0V)
0010
0
CAL0
R/W
CC
SUT1..0
OSCCAL
), the CKDIV8
00
01
10
11
32

Related parts for ATMEGA32U4-MUR