ATMEGA16-16AU SL383 Atmel, ATMEGA16-16AU SL383 Datasheet - Page 230

• Manufacturer Part Number: ATMEGA16-16AU SL383
• Description: IC MCU 8BIT 16KB FLASH 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16-16AU SL383

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Boundary-scan Chain
Boundary-scan
Specific JTAG
Instructions
EXTEST; $0
IDCODE; $1
SAMPLE_PRELOAD;
$2
2466T–AVR–07/10
Figure 115. Reset Register
The Boundary-scan Chain has the capability of driving and observing the logic levels on the dig-
ital I/O pins, as well as the boundary between digital and analog logic for analog circuitry having
Off-chip connections.
See
The instruction register is 4-bit wide, supporting up to 16 instructions. Listed below are the JTAG
instructions useful for Boundary-scan operation. Note that the optional HIGHZ instruction is not
implemented, but all outputs with tri-state capability can be set in high-impedant state by using
the AVR_RESET instruction, since the initial state for all port pins is tri-state.
As a definition in this datasheet, the LSB is shifted in and out first for all Shift Registers.
The OPCODE for each instruction is shown behind the instruction name in hex format. The text
describes which Data Register is selected as path between TDI and TDO for each instruction.
Mandatory JTAG instruction for selecting the Boundary-scan Chain as Data Register for testing
circuitry external to the AVR package. For port-pins, Pull-up Disable, Output Control, Output
Data, and Input Data are all accessible in the scan chain. For Analog circuits having Off-chip
connections, the interface between the analog and the digital logic is in the scan chain. The con-
tents of the latched outputs of the Boundary-scan chain is driven out as soon as the JTAG IR-
register is loaded with the EXTEST instruction.
The active states are:
•
•
•
Optional JTAG instruction selecting the 32-bit ID-register as Data Register. The ID-register con-
sists of a version number, a device number and the manufacturer code chosen by JEDEC. This
is the default instruction after power-up.
The active states are:
•
•
Mandatory JTAG instruction for pre-loading the output latches and talking a snap-shot of the
input/output pins without affecting the system operation. However, the output latches are not
connected to the pins. The Boundary-scan Chain is selected as Data Register.
Capture-DR: Data on the external pins are sampled into the Boundary-scan Chain.
Shift-DR: The Internal Scan Chain is shifted by the TCK input.
Update-DR: Data from the scan chain is applied to output pins.
Capture-DR: Data in the IDCODE-register is sampled into the Boundary-scan Chain.
Shift-DR: The IDCODE scan chain is shifted by the TCK input.
“Boundary-scan Chain” on page 232
External Reset Sources
From other Internal and
From
ClockDR · AVR_RESET
TDI
D
for a complete description.
Q
TDO
To
ATmega16(L)
Internal Reset
230