PIC24HJ64GP502-I/SP Microchip Technology, PIC24HJ64GP502-I/SP Datasheet - Page 2

IC PIC MCU FLASH 64K 28DIP

PIC24HJ64GP502-I/SP

Manufacturer Part Number
PIC24HJ64GP502-I/SP
Description
IC PIC MCU FLASH 64K 28DIP
Manufacturer
Microchip Technology
Series
PIC® 24Hr

Specifications of PIC24HJ64GP502-I/SP

Core Size
16-Bit
Program Memory Size
64KB (22K x 24)
Core Processor
PIC
Speed
40 MIPs
Connectivity
CAN, I²C, IrDA, LIN, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
21
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 10x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-DIP (0.300", 7.62mm)
Controller Family/series
PIC24
No. Of I/o's
21
Ram Memory Size
4KB
Cpu Speed
40MIPS
No. Of Timers
7
No. Of Pwm Channels
4
Embedded Interface Type
I2C, SPI, UART
Rohs Compliant
Yes
Processor Series
PIC24HJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
8 KB
Interface Type
I2C, SPI, UART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
21
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM300027
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 10 Channel / 12 bit, 10 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164337 - MODULE SOCKET FOR PM3 40DIP
Eeprom Size
-
Lead Free Status / Rohs Status
 Details

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC24HJ64GP502-I/SP
Manufacturer:
MICROCHIP
Quantity:
12 000
FIGURE 2-2:
TABLE 2-1:
DS70152H-page 2
MCLR
V
V
V
PGEC1
PGED1
PGEC2
PGED2
PGEC3
PGED3
Legend: I = Input
Note 1:
DD
SS
CAP
Pin Name
Note 1: These are typical operating voltages. Refer
and AV
and AV
C
EFC
2: It is important for the low-ESR capacitor to
All power supply and ground pins must be connected, including analog supplies (AV
(AV
SS
DD (1)
to
and Timing Requirements”
operating ranges of V
be placed as close as possible to the V
pin.
3.3V
(1)
SS
TABLE 8-1: “AC/DC Characteristics
).
PINS USED DURING PROGRAMMING
Pin Name
CONNECTIONS FOR THE
ON-CHIP REGULATOR
V
V
V
PGEC1
PGED1
PGEC2
PGED2
PGEC3
PGED3
MCLR
DD
CAP
SS
V
V
V
dsPIC33F/PIC24H
CAP
DD
SS
O = Output
DD
and V
Pin Type
CAP
for the full
I/O
I/O
I/O
P
P
P
P
I
I
I
.
P = Power
CAP
Programming Enable
Power Supply
Ground
CPU Logic Filter Capacitor Connection
Primary Programming Pin Pair: Serial Clock
Primary Programming Pin Pair: Serial Data
Secondary Programming Pin Pair: Serial Clock
Secondary Programming Pin Pair: Serial Data
Tertiary Programming Pin Pair: Serial Clock
Tertiary Programming Pin Pair: Serial Data
During Programming
2.2
The program Flash memory on the dsPIC33F/PIC24H
has a specific write/erase requirement that must be
adhered to, for proper device operation. The rule is that
any given word in memory must not be written without
first erasing the page in which it is located. Thus, the
easiest way to conform to this rule is to write all the data
in a programming block within one write cycle. The
programming methods specified in this document
comply with this requirement.
2.3
The pins that are used for programming are listed in
Table
Note:
Note:
2-1.
Program Memory Write/Erase
Requirements
Pins Used During Programming
A
programmed twice before an erase, but
only if (a) the same data is used in both
program operations or (b) bits containing
‘1’ are set to ‘0’ but no ‘0’ is set to ‘1’.
Refer to the specific device data sheet for
complete pin diagrams of the dsPIC33F/
PIC24H devices.
Pin Description
program
© 2010 Microchip Technology Inc.
memory
DD
) and ground
word
can
be

Related parts for PIC24HJ64GP502-I/SP