ATMEGA644A-PU Atmel, ATMEGA644A-PU Datasheet - Page 138

IC MCU AVR 64K FLASH 40PDIP

ATMEGA644A-PU

Manufacturer Part Number
ATMEGA644A-PU
Description
IC MCU AVR 64K FLASH 40PDIP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheets

Specifications of ATMEGA644A-PU

Core Processor
AVR
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
64KB (32K x 16)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Processor Series
ATmega
Core
AVR
Data Bus Width
8 bit
Data Ram Size
4 KB
Interface Type
JTAG, TWI, SPI, USART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
32
Number Of Timers
3
Operating Supply Voltage
3.3 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 40 C
Operating Temperature Range
- 40 C to + 85 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
15.11.7
15.11.8
8272A–AVR–01/10
ICR1H and ICR1L – Input Capture Register 1
TIMSK1 – Timer/Counter1 Interrupt Mask Register
The Input Capture is updated with the counter (TCNTn) value each time an event occurs on the
ICPn pin (or optionally on the Analog Comparator output for Timer/Counter1). The Input Capture
can be used for defining the counter TOP value.
The Input Capture Register is 16-bit in size. To ensure that both the high and low bytes are read
simultaneously when the CPU accesses these registers, the access is performed using an 8-bit
temporary High Byte Register (TEMP). This temporary register is shared by all the other 16-bit
registers.
• Bit 7:6 – Res: Reserved Bits
These bits are unused bits in the ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P,
and will always read as zero.
• Bit 5 – ICIE1: Timer/Counter1, Input Capture Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Counter1 Input Capture interrupt is enabled. The corresponding Interrupt
Vector (see “Interrupts” on page 62) is executed when the ICF1 Flag, located in TIFR1, is set.
• Bit 4:3 – Res: Reserved Bits
These bits are unused bits in the ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P,
and will always read as zero.
• Bit 2 – OCIE1B: Timer/Counter1, Output Compare B Match Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Counter1 Output Compare B Match interrupt is enabled. The corresponding
Interrupt Vector (see “Interrupts” on page 62) is executed when the OCF1B Flag, located in
TIFR1, is set.
• Bit 1 – OCIE1A: Timer/Counter1, Output Compare A Match Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Counter1 Output Compare A Match interrupt is enabled. The corresponding
Interrupt Vector (see “Interrupts” on page 62) is executed when the OCF1A Flag, located in
TIFR1, is set.
164A/164PA/324A/324PA/644A/644PA/1284/1284P
Bit
(0x87)
(0x86)
Read/Write
Initial Value
Bit
(0x6F)
Read/Write
Initial Value
See Section “15.3” on page 114.
R/W
R
7
0
7
0
R/W
R
6
0
6
0
ICIE1
R/W
R/W
5
0
5
0
R/W
R
4
0
4
0
ICR1[15:8]
ICR1[7:0]
R/W
R
3
0
3
0
OCIE1B
R/W
R/W
2
0
2
0
OCIE1A
R/W
R/W
1
0
1
0
TOIE1
R/W
R/W
0
0
0
0
TIMSK1
ICR1H
ICR1L
138

Related parts for ATMEGA644A-PU