DSPIC33FJ128MC708A-I/PT Microchip Technology, DSPIC33FJ128MC708A-I/PT Datasheet - Page 67

• Manufacturer Part Number: DSPIC33FJ128MC708A-I/PT
• Description: IC DSPIC MCU/DSP 128K 80-TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128MC708A-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (128K x 8)
• Package / Case: 80-TFQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 69
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC33F
• Core: dsPIC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 69
• Data Ram Size: 16 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
• Minimum Operating Temperature: - 40 C
• Package: 80TQFP
• Device Core: dsPIC
• Family Name: dsPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 36-chx10-bit|36-chx12-bit
• Number Of Timers: 9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1001 - DSPIC33 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Modulo Addressing can operate in either data or program
space (since the Data Pointer mechanism is essentially
the same for both). One circular buffer can be supported
in each of the X (which also provides the pointers into
program space) and Y data spaces. Modulo Addressing
can operate on any W register pointer. However, it is not
advisable to use W14 or W15 for Modulo Addressing,
since these two registers are used as the Stack Frame
Pointer and Stack Pointer, respectively.
In general, any particular circular buffer can only be
configured to operate in one direction, as there are
certain restrictions on the buffer start address (for incre-
menting buffers) or end address (for decrementing
buffers), based upon the direction of the buffer.
The only exception to the usage restrictions is for
buffers which have a power-of-2 length. As these
buffers satisfy the start and end address criteria, they
may operate in a bidirectional mode (i.e., address
boundary checks will be performed on both the lower
and upper address boundaries).
4.4.1
The Modulo Addressing scheme requires that a starting
and ending address be specified and loaded into the
16-bit Modulo Buffer Address registers: XMODSRT,
XMODEND,
Table 4-1).
FIGURE 4-7:
 2009 Microchip Technology Inc.
Note:
Address
0x1100
0x1163
Byte
START AND END ADDRESS
Y space Modulo Addressing EA calcula-
tions assume word-sized data (LSb of
every EA is always clear).
YMODSRT
Start Addr = 0x1100
End Addr = 0x1163
Length = 0x0032 Words
MODULO ADDRESSING OPERATION EXAMPLE
dsPIC33FJXXXMCX06A/X08A/X10A
and
YMODEND
MOV
MOV
MOV
MOV
MOV
MOV
MOV
MOV
DO
MOV
AGAIN: INC
(see
Preliminary
#0x1100, W0
W0, XMODSRT
#0x1163, W0
W0, MODEND
#0x8001, W0
W0, MODCON
#0x0000, W0
#0x1110, W1
AGAIN, #0x31
W0, [W1++]
W0, W0
The length of a circular buffer is not directly specified. It
is
corresponding start and end addresses. The maximum
possible length of the circular buffer is 32K words
(64 Kbytes).
4.4.2
The Modulo and Bit-Reversed Addressing Control
register, MODCON<15:0>, contains enable flags as well
as a W register field to specify the W Address registers.
The XWM and YWM fields select which registers will
operate with Modulo Addressing. If XWM = 15, X RAGU
and X WAGU Modulo Addressing are disabled. Similarly,
if YWM = 15, Y AGU Modulo Addressing is disabled.
The X Address Space Pointer W register (XWM) to
which Modulo Addressing is to be applied is stored in
MODCON<3:0> (see Table 4-1). Modulo Addressing is
enabled for X data space when XWM is set to any value
other than 15 and the XMODEN bit is set at
MODCON<15>.
The Y Address Space Pointer W register (YWM) to
which Modulo Addressing is to be applied is stored in
MODCON<7:4>. Modulo Addressing is enabled for Y
data space when YWM is set to any value other than 15
and the YMODEN bit is set at MODCON<14>.
determined
;set modulo start address
;set modulo end address
;enable W1, X AGU for modulo
;W0 holds buffer fill value
;point W1 to buffer
;fill the 50 buffer locations
;fill the next location
;increment the fill value
W ADDRESS REGISTER
SELECTION
by
the
difference
DS70594B-page 67
between
the