LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 294

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
6.5.1 Cursor operation
6.5 Hardware cursor
Table 251. Palette data storage for STN color modes.
For monochrome STN mode, only the red palette field bits [4:1] are used. However, in
STN color mode the green and blue [4:1] are also used. Only 4 bits per color are used,
because the gray scaler only supports 16 different shades per color.
Table 12–252
mode.
Table 252. Palette data storage for STN monochrome mode.
The hardware cursor is an integral part of the LCD controller. It uses the LCD timing
module to provide an indication of the current scan position coordinate, and intercepts the
pixel stream between the palette logic and the gray scale/output multiplexer.
All cursor programming registers are accessed through the LCD slave interface. This also
provides a read/write port to the cursor image RAM.
The hardware cursor is contained in a dual port RAM. It is programmed by software
through the AHB slave interface. The AHB slave interface also provides access to the
hardware cursor control registers. These registers enable you to modify the cursor
position and perform various other functions.
When enabled, the hardware cursor uses the horizontal and vertical synchronization
signals, along with a pixel clock enable and various display parameters to calculate the
current scan coordinate.
Bit(s)
5
4:1
0
Bit(s)
31
30:27
26
25:22
21
20:17
16
15
14:11
10
9:6
5
4:1
0
Name
(RGB format)
G[0]
R[4:1]
R[0]
shows the bit representation of the palette data for the STN monochrome
Name
-
-
-
-
-
Y[3:0]
-
-
-
-
-
-
Y[3:0]
-
Rev. 04 — 26 August 2009
Description
(RGB format)
Unused
Red palette data
Unused
Description
Unused
Unused
Unused
Unused
Unused
Intensity data
Unused
Unused
Unused
Unused
Unused
Unused
Intensity data
Unused
Name
(BGR format)
G[0]
B[4:1]
B[0]
Chapter 12: LPC24XX LCD controller
Description
(BGR format)
Unused
Blue palette data
Unused
UM10237
© NXP B.V. 2009. All rights reserved.
294 of 792