LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 301

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
6.11.2.1 Next base address update interrupt
6.11.2.2 FIFO underflow interrupt
6.11.1 Master bus error interrupt
6.11.2 Vertical compare interrupt
Each of the four individual maskable interrupts is enabled or disabled by changing the
mask bits in the LCD_INT_MSK register. These interrupts are also combined into a single
overall interrupt, which is asserted if any of the individual interrupts are both asserted and
unmasked. Provision of individual outputs in addition to a combined interrupt output
enables use of either a global interrupt service routine, or modular device drivers to
handle interrupts.
The status of the individual interrupt sources can be read from the LCD_INTRAW register.
The master bus error interrupt is asserted when an ERROR response is received by the
master interface during a transaction with a slave. When such an error is encountered, the
master interface enters an error state and remains in this state until clearance of the error
has been signaled to it. When the respective interrupt service routine is complete, the
master bus error interrupt may be cleared by writing a 1 to the BERIC bit in the
LCD_INTCLR register. This action releases the master interface from its ERROR state to
the start of FRAME state, and enables fresh frame of data display to be initiated.
The vertical compare interrupt asserts when one of four vertical display regions, selected
using the LCD_CTRL register, is reached. The interrupt can be made to occur at the start
of:
The interrupt may be cleared by writing a 1 to the VcompIC bit in the LCD_INTCLR
register.
The LCD next base address update interrupt asserts when either the LCDUPBASE or
LCDLPBASE values have been transferred to the LCDUPCURR or LCDLPCURR
incrementers respectively. This signals to the system that it is safe to update the
LCDUPBASE or the LCDLPBASE registers with new frame base addresses if required.
The interrupt can be cleared by writing a 1 to the LNBUIC bit in the LCD_INTCLR register
The FIFO underflow interrupt asserts when internal data is requested from an empty DMA
FIFO. Internally, upper and lower panel DMA FIFO underflow interrupt signals are
generated.
The interrupt can be cleared by writing a 1 to the FUFIC bit in the LCD_INTCLR register.
•
•
•
•
•
•
Next base address update interrupt.
FIFO underflow interrupt.
Vertical synchronization.
Back porch.
Active video.
Front porch.
Rev. 04 — 26 August 2009
Chapter 12: LPC24XX LCD controller
UM10237
© NXP B.V. 2009. All rights reserved.
301 of 792