LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 366

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
11.4 Read Current Frame Number (Command: 0xF5, Data: read 1 or 2
11.5 Read Test Register (Command: 0xFD, Data: read 2 bytes)
11.6 Set Device Status (Command: 0xFE, Data: write 1 byte)
bytes)
Returns the frame number of the last successfully received SOF. The frame number is
eleven bits wide. The frame number returns least significant byte first. In case the user is
only interested in the lower 8 bits of the frame number, only the first byte needs to be read.
The test register is 16 bits wide. It returns the value of 0xA50F if the USB clocks (usbclk
and AHB slave clock) are running.
The Set Device Status command sets bits in the Device Status Register.
Table 351. Set Device Status Register bit description
Bit Symbol
0
1
2
•
•
In case no SOF was received by the device at the beginning of a frame, the frame
number returned is that of the last successfully received SOF.
In case the SOF frame number contained a CRC error, the frame number returned will
be the corrupted frame number as received by the device.
CON
CON_CH
SUS
Value Description
0
1
0
1
0
1
Rev. 04 — 26 August 2009
The Connect bit indicates the current connect status of the
device. It controls the CONNECT output pin, used for
SoftConnect. Reading the connect bit returns the current connect
status. This bit is cleared by hardware when the V
is LOW for more than 3 ms. The 3 ms delay filters out temporary
dips in the V
Writing a 0 will make the CONNECT pin go HIGH.
Writing a 1 will make the CONNECT pin go LOW..
Connect Change.
This bit is cleared when read.
This bit is set when the device’s pull-up resistor is disconnected
because V
generated when this bit is 1.
Suspend: The Suspend bit represents the current suspend state.
When the device is suspended (SUS = 1) and the CPU writes a 0
into it, the device will generate a remote wakeup. This will only
happen when the device is connected (CON = 1). When the
device is not connected or not suspended, writing a 0 has no
effect. Writing a 1 to this bit has no effect.
This bit is reset to 0 on any activity.
This bit is set to 1 when the device hasn’t seen any activity on its
upstream port for more than 3 ms.
BUS
BUS
disappeared. The DEV_STAT interrupt is
voltage.
Chapter 13: LPC24XX USB device controller
BUS
UM10237
status input
© NXP B.V. 2009. All rights reserved.
366 of 792
Reset
value
0
0
0