LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 378

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
14.4.10 Packet_valid
14.4.6 DMA_buffer_length
14.4.7 DMA_buffer_start_addr
14.4.8 DD_retired
14.4.9 DD_status
This indicates the depth of the DMA buffer allocated for transferring the data. The DMA
engine will stop using this descriptor when this limit is reached and will look for the next
descriptor.
In Normal mode operation, software sets this value for both IN and OUT endpoints. In
ATLE mode operation, software sets this value for IN endpoints only. For OUT endpoints,
hardware sets this value using the extracted length of the data stream.
For isochronous endpoints, DMA_buffer_length is specified in number of packets, for
non-isochronous endpoints in bytes.
The address where the data is read from or written to. This field is updated each time the
DMA engine finishes transferring a packet.
This bit is set by hardware when the DMA engine finishes the current descriptor. This
happens when the end of the buffer is reached, a short packet is transferred
(non-isochronous endpoints), or an error condition is detected.
The status of the DMA transfer is encoded in this field. The following codes are defined:
This bit is used for isochronous endpoints. It indicates whether the last packet transferred
to the memory is received with errors or not. This bit is set if the packet is valid, i.e., it was
received without errors. See
381
This bit is unnecessary for non-isochronous endpoints because a DMA request is
generated only for packets without errors, and thus Packet_valid will always be set when
the request is generated.
•
•
•
•
•
•
NotServiced - No packet has been transferred yet.
BeingServiced - At least one packet is transferred.
NormalCompletion - The DD is retired because the end of the buffer is reached and
there were no errors. The DD_retired bit is also set.
DataUnderrun - Before reaching the end of the DMA buffer, the USB transfer is
terminated because a short packet is received. The DD_retired bit is also set.
DataOverrun - The end of the DMA buffer is reached in the middle of a packet
transfer. This is an error situation. The DD_retired bit is set. The present DMA count
field is equal to the value of DMA_buffer_length. The packet must be re-transmitted
from the endpoint buffer in another DMA transfer. The corresponding
EPxx_DMA_ENABLE bit in USBEpDMASt is cleared.
SystemError - The DMA transfer being serviced is terminated because of an error on
the AHB bus. The DD_retired bit is not set in this case. The corresponding
EPxx_DMA_ENABLE in USBEpDMASt is cleared. Since a system error can happen
while updating the DD, the DD fields in RAM may be unreliable.
for isochronous endpoint operation.
Rev. 04 — 26 August 2009
Section 13–14.6 “Isochronous endpoint operation” on page
Chapter 13: LPC24XX USB device controller
UM10237
© NXP B.V. 2009. All rights reserved.
378 of 792