LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 467

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

1. How to read this chapter
2. Basic configuration
3. CAN controllers
UM10237_4
User manual
The CAN controller in available on parts LPC2458 and LPC2460/68/70/78.
The CAN1/2 peripherals are configured using the following registers:
Controller Area Network (CAN) is the definition of a high performance communication
protocol for serial data communication. The CAN Controller is designed to provide a full
implementation of the CAN-Protocol according to the CAN Specification Version 2.0B.
Microcontrollers with this on-chip CAN controller are used to build powerful local networks
by supporting distributed real-time control with a very high level of security. The
applications are automotive, industrial environments, and high speed networks as well as
low cost multiplex wiring. The result is a strongly reduced wiring harness and enhanced
diagnostic and supervisory capabilities.
The CAN block is intended to support multiple CAN buses simultaneously, allowing the
device to be used as a gateway, switch, or router among a number of CAN buses in
various applications.
The CAN module consists of two elements: the controller and the Acceptance Filter. All
registers and the RAM are accessed as 32 bit words.
1. Power: In the PCONP register
2. Peripheral clock: In the PCLK_SEL0 register
3. Wakeup: Use the INTWAKE register
4. Pins: Select CAN1/2 pins and pin modes in registers PINSELn and PINMODEn (see
5. Interrupts: CAN interrupts are enabled using the CAN1/2IER registers
6. CAN controller initialization: see CANMOD register
UM10237
Chapter 18: LPC24XX CAN controllers CAN1/2
Rev. 04 — 26 August 2009
Remark: On reset, the CAN1/2 blocks are disabled (PCAN1/2 = 0).
for the acceptance filter, PCLK_ACF. PCLK_CAN1/2 and PCLK_ACF must be set to
the same value.
Remark: If CAN baudrates above 100 kbit/s (see
select the IRC as the clock source (see
wake up the microcontroller from Power-down mode.
Section
(Table
(Table
18–424). Interrupts are enabled in the VIC using the VICIntEnable register
7–106).
9–5).
Rev. 04 — 26 August 2009
(Table
(Table
4–63), set bits PCAN1/2.
Table
4–62) to enable the CAN controllers to
(Table
4–42).
Table
4–56), select PCLK_CAN1/2 and,
(Section
18–425) are needed, do not
18–8.1).
© NXP B.V. 2009. All rights reserved.
User manual
467 of 792