LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 472

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
Fig 76. Global Self-Test (high-speed CAN Bus example)
TX Buffer
RX Buffer
TX Buffer
LPC24xx
TX Buffer
Both self-tests are using the ‘Self Reception’ feature of the CAN Controller. With the Self
Reception Request, the transmitted message is also received and stored in the receive
buffer. Therefore the acceptance filter has to be configured accordingly. As soon as the
CAN message is transmitted, a transmit and a receive interrupt are generated, if enabled.
Global self test
A Global Self-Test can for example be used to verify the chosen configuration of the CAN
Controller in a given CAN system. As shown in
node, which is acknowledging each CAN message has to be connected to the CAN bus.
Initiating a Global Self-Test is similar to a normal CAN transmission. In this case the
transmission of a CAN message(s) is initiated by setting Self Reception Request bit
(SRR) in conjunction with the selected Message Buffer bits (STB3, STB2, STB1) in the
CAN Controller Command register (CANCMR).
Local self test
The Local Self-Test perfectly fits for single node tests. In this case an acknowledge from
other nodes is not needed. As shown in the Figure below, a CAN transceiver with an
appropriate CAN bus termination has to be connected to the LPC. The CAN Controller
has to be put into the 'Self Test Mode' by setting the STM bit in the CAN Controller Mode
register (CANMOD). Hint: Setting the Self Test Mode bit (STM) is possible only when the
CAN Controller is in Reset Mode.
A message transmission is initiated by setting Self Reception Request bit (SRR) in
conjunction with the selected Message Buffer(s) (STB3, STB2, STB1).
Fig 77. Local self test (high-speed CAN Bus example)
Transceiver
Rev. 04 — 26 August 2009
CAN Bus
TX Buffer
TX Buffer
LPC24xx
RX Buffer
TX Buffer
Chapter 18: LPC24XX CAN controllers CAN1/2
Transceiver
Figure
18–76, at least one other CAN
UM10237
© NXP B.V. 2009. All rights reserved.
ack
472 of 792