LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 480

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
8.4 Interrupt and Capture Register (CAN1ICR - 0xE004 400C, CAN2ICR -
RX Error Counter = (CANxGSR AND 0x00FF0000) / 0x00010000
Note that a CPU-forced content change of the RX Error Counter is possible only if the
Reset Mode was entered previously. An Error Status change (Status Register), an Error
Warning or an Error Passive Interrupt forced by the new register content will not occur
until the Reset Mode is cancelled again.
TX error counter
The TX Error Counter Register, which is part of the Status Register, reflects the current
value of the Transmit Error Counter. In Operating Mode this register appears to the CPU
as a read only memory. After hardware reset this register is initialized to ’0’. A write access
to this register is possible only in Reset Mode. If a bus-off event occurs, the TX Error
Counter is initialized to 127 to count the minimum protocol-defined time (128 occurrences
of the Bus-Free signal). Reading the TX Error Counter during this time gives information
about the status of the Bus-Off recovery. If Bus Off is active, a write access to TXERR in
the range of 0 to 254 clears the Bus Off Flag and the controller will wait for one occurrence
of 11 consecutive recessive bits (bus free) after clearing of Reset Mode. The Tx error
counter is determined as follows:
TX Error Counter = (CANxGSR AND 0xFF000000) / 0x01000000
Writing 255 to TXERR allows initiation of a CPU-driven Bus Off event. Note that a
CPU-forced content change of the TX Error Counter is possible only if the Reset Mode
was entered previously. An Error or Bus Status change (Status Register), an Error
Warning, or an Error Passive Interrupt forced by the new register content will not occur
until the Reset Mode is cancelled again. After leaving the Reset Mode, the new TX
Counter content is interpreted and the Bus Off event is performed in the same way as if it
was forced by a bus error event. That means, that the Reset Mode is entered again, the
TX Error Counter is initialized to 127, the RX Counter is cleared, and all concerned Status
and Interrupt Register Bits are set. Clearing of Reset Mode now will perform the protocol
defined Bus Off recovery sequence (waiting for 128 occurrences of the Bus-Free signal).
If the Reset Mode is entered again before the end of Bus Off recovery (TXERR>0), Bus
Off keeps active and TXERR is frozen.
0xE004 800C)
Bits in this register indicate information about events on the CAN bus. This register is
read-only. Bits not listed read as 0 and should be written as 0.
The Interrupt flags of the Interrupt and Capture Register allow the identification of an
interrupt source. When one or more bits are set, a CAN interrupt will be indicated to the
CPU. After this register is read from the CPU all interrupt bits are reset except of the
Receive Interrupt bit. The Interrupt Register appears to the CPU as a read only memory.
Bits 1 thru 10 clear when they are read.
Bits 16-23 are captured when a bus error occurs. At the same time, if the BEIE bit in
CANIER is 1, the BEI bit in this register is set, and a CAN interrupt can occur.
Rev. 04 — 26 August 2009
Chapter 18: LPC24XX CAN controllers CAN1/2
UM10237
© NXP B.V. 2009. All rights reserved.
480 of 792