LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 639

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
Table 557. PWM0 and PWM1 register map
[1]
UM10237_4
User manual
Generic
Name
MR4
MR5
MR6
PCR
LER
CTCR
Reset Value relects the data stored in used bits only. It does not include reserved bits content.
Description
Match Register 4. MR4 can be enabled in the MCR to
reset the TC, stop both the TC and PC, and/or generate
an interrupt when it matches the TC. In addition, a match
between this value and the TC clears PWM4 in either
edge mode, and sets PWM5 if it’s in double-edge mode.
Match Register 5. MR5 can be enabled in the MCR to
reset the TC, stop both the TC and PC, and/or generate
an interrupt when it matches the TC. In addition, a match
between this value and the TC clears PWM5 in either
edge mode, and sets PWM6 if it’s in double-edge mode.
Match Register 6. MR6 can be enabled in the MCR to
reset the TC, stop both the TC and PC, and/or generate
an interrupt when it matches the TC. In addition, a match
between this value and the TC clears PWM6 in either
edge mode.
PWM Control Register. Enables PWM outputs and
selects PWM channel types as either single edge or
double edge controlled.
Load Enable Register. Enables use of new PWM match
values.
Count Control Register. The CTCR selects between
Timer and Counter mode, and in Counter mode selects
the signal and edge(s) for counting.
6.1 PWM Interrupt Register (PWM0IR - 0xE001 4000 and PWM1IR
0xE001 8000)
The PWM Interrupt register consists of eleven bits
interrupts and four reserved. If an interrupt is generated then the corresponding bit in the
PWMIR will be high. Otherwise, the bit will be low. Writing a logic one to the corresponding
IR bit will reset the interrupt. Writing a zero has no effect.
Table 558: PWM Interrupt Register (PWM0IR - address 0xE001 4000 and PWM1IR address
Bit
0
1
2
3
4
5
7:6
8
Symbol
PWMMR0 Interrupt Interrupt flag for PWM match channel 0.
PWMMR1 Interrupt Interrupt flag for PWM match channel 1.
PWMMR2 Interrupt Interrupt flag for PWM match channel 2.
PWMMR3 Interrupt Interrupt flag for PWM match channel 3.
PWMCAP0
Interrupt
PWMCAP1
Interrupt
-
PWMMR4 Interrupt Interrupt flag for PWM match channel 4.
0xE001 8000) bit description
Rev. 04 — 26 August 2009
Description
Interrupt flag for capture input 0
Interrupt flag for capture input 1 (available in PWM1IR only;
this bit is reserved in PWM0IR).
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
Chapter 25: LPC24XX Pulse Width Modulator PWM0/PWM1
Access Reset
R/W
R/W
R/W
R/W
R/W
R/W
Value
0
0
0
0
0
0
(Table
[1]
PWM0 Address
& Name
0xE001 4040
PWM0MR
0xE001 4044
PWM0MR
0xE001 4048
PWM0MR
0xE001 404C
PWM0PCR
0xE001 4050
PWM0LER
0xE001 4070
PWM0CTCR
25–558), seven for the match
UM10237
© NXP B.V. 2009. All rights reserved.
PWM1 Address
& Name
0xE001 8040
PWM1MR
0xE001 8044
PWM1MR
0xE001 8048
PWM1MR
0xE001 804C
PWM1PCR
0xE001 8050
PWM1LER
0xE001 8070
PWM1CTCR
639 of 792
Reset
Value
0
0
0
0
0
0
-
0