STM8S103F3P6 STMicroelectronics, STM8S103F3P6 Datasheet - Page 50

• Manufacturer Part Number: STM8S103F3P6
• Description: MCU 8BIT 8KB FLASH 20-TSSOP
• Manufacturer: STMicroelectronics
• Series: STM8Sr

Specifications of STM8S103F3P6

• Core Processor: STM8
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 640 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.95 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-TSSOP
• Processor Series: STM8S10x
• Core: STM8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 7
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWSTM8
• Development Tools By Supplier: STM8/128-MCKIT, STM8S-DISCOVERY, ST-LINK, STICE-SYS001, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 5 Channel
• Featured Product: STM32 Cortex-M3 Companion Products
• For Use With: 497-10593 - KIT STARTER FOR STM8S207/8 SER
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Electrical characteristics
50/113
Symbol
I
I
I
I
ΣI
(1)
(2)
(3)
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
pads, there is no positive injection current, and the corresponding V
(4)
should be avoided as this significantly reduces the accuracy of the conversion being performed on
another analog input. It is recommended to add a Schottky diode (pin to ground) to standard analog pins
which may potentially inject negative current. Any positive injection current within the limits specified for
I
(5)
of the positive and negative injected currents (instantaneous values). These results are based on
characterization with ΣI
VDD
VSS
IO
INJ(PIN)
INJ(PIN)
I
INJ(PIN)
ADC accuracy vs. negative injection current: Injecting negative current on any of the analog input pins
Data based on characterization results, not tested in production.
All power (V
When several inputs are submitted to a current injection, the maximum ΣI
INJ(PIN)
(3) (4)
and ΣI
(3)
must never be exceeded. This is implicitly insured if V
Symbol
T
T
INJ(PIN)
STG
J
DD
) and ground (V
in the I/O port pin characteristics section does not affect the ADC accuracy.
Ratings
Ratings
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRST pin
Injected current on OSCIN pin
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
INJ(PIN)
Storage temperature range
Maximum junction temperature
IN
>V
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
SS
Table 17: Current characteristics
) pins must always be connected to the external supply.
Table 18: Thermal characteristics
DD
DocID15441 Rev 6
SS
power lines (source)
ground lines (sink)
(5)
STM8S103K3 STM8S103F3 STM8S103F2
IN
maximum is respected. If V
IN
(2)
(2)
maximum must always be respected
IN
<V
INJ(PIN)
Value
-65 to +150
150
(5)
INJ(PIN)
SS
. For true open-drain
value. A positive
is the absolute sum
Max
100
80
20
- 20
± 4
± 4
± 4
± 20
(1)
IN
maximum
Unit
mA
Unit
°C