ST62T25CM6 STMicroelectronics, ST62T25CM6 Datasheet - Page 26

• Manufacturer Part Number: ST62T25CM6
• Description: IC MCU 8BIT OTP 4K 28 SOIC
• Manufacturer: STMicroelectronics
• Series: ST6r

Specifications of ST62T25CM6

• Core Processor: ST6
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, WDT
• Number Of I /o: 20
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: OTP
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6 V
• Data Converters: A/D 16x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: ST62T2x
• Core: ST6
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 20
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, ST622XC-KIT/110, STREALIZER-II
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2101-5

ST6215CM-Auto ST6225CM-Auto
RESET (Cont’d)
5.3.4 Watchdog Reset
The MCU provides a Watchdog timer function in
order to be able to recover from software hang-
ups. If the Watchdog register is not refreshed be-
fore an end-of-count condition is reached, a
Watchdog reset is generated.
After a Watchdog reset, the MCU restarts in the
same way as if a Reset was generated by the RE-
SET pin.
Note: When a watchdog reset occurs, the RESET
pin is tied low for very short time period, to flag the
reset phase. This time is not long enough to reset
external circuits.
For more details refer to the Watchdog Timer
chapter.
5.3.5 LVD Reset
Two different RESET sequences caused by the in-
ternal LVD circuitry can be distinguished:
■
■
During an LVD reset, the RESET pin is pulled low
when V
edge).
For more details, refer to the LVD chapter.
Caution: Do not externally connect directly the
RESET pin to V
component in case of internal RESET (Watchdog
or LVD).
Figure 15. Simple External Reset Circuitry
26/100
1
Typical: R = 10K
Power-On RESET
Voltage Drop RESET
V
DD
DD
C = 10nF
<V
IT+
DD
(rising edge) or V
R
C
, this may cause damage to the
V
RESET
DD
R > 4.7 K
ST62xx
DD
<V
IT-
(falling
Figure 16. Reset Processing
YES
FROM RESET LOCATIONS
FETCH INSTRUCTION
INT LATCH CLEARED
ON ADDRESS BUS
NMI MODE FLAGS
IS RESET STILL
NMI MASK SET
(IF PRESENT)
FFEh/FFFh
INTERNAL
PUT FFEh
PRESENT?
LOAD PC
SELECT
RESET
RESET
CLOCK CYCLE
NO
DELAY
2048