STM32F101C8U6 STMicroelectronics, STM32F101C8U6 Datasheet - Page 32

• Manufacturer Part Number: STM32F101C8U6
• Description: MCU 32BIT ARM 128K FLASH 48-QFN
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101C8U6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP Exposed Pad, 48-eLQFP, 48-HLQFP
• Processor Series: STM32F101x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 10 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 10 Channel
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• For Use With: 497-10030 - STARTER KIT FOR STM32497-6438 - BOARD EVALUTION FOR STM32 512K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Electrical characteristics
5.3
5.3.1
32/87
Table 6.
1. All main power (V
2. Negative injection disturbs the analog performance of the device. See note in
3. Positive injection is not possible on these I/Os. A negative injection is induced by V
4.
5. When several inputs are submitted to a current injection, the maximum ΣI
Table 7.
Operating conditions
General operating conditions
Table 8.
Symbol
V
supply, in the permitted range.
characteristics.
never be exceeded. Refer to
values.
never be exceeded. Refer to
values.
positive and negative injected currents (instantaneous values).
f
f
I
A positive injection is induced by V
f
PCLK1
PCLK2
ΣI
V
DDA
INJ(PIN)
HCLK
Symbol
V
BAT
DD
INJ(PIN)
Symbol
I
I
VDD
VSS
I
T
IO
(1)
STG
T
J
(2)
Current characteristics
Thermal characteristics
General operating conditions
Internal AHB clock frequency
Internal APB1 clock frequency
Internal APB2 clock frequency
Standard operating voltage
Analog operating voltage
(ADC not used)
Analog operating voltage
(ADC used)
Backup operating voltage
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on five volt tolerant pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
, V
Storage temperature range
Maximum junction temperature
DDA
Parameter
) and ground (V
Table 5: Voltage characteristics
Table 5: Voltage characteristics
Doc ID 13586 Rev 14
IN
>V
DD
DD
SS
/V
Ratings
SS
while a negative injection is induced by V
DDA
ground lines (sink)
, V
Ratings
SSA
Must be the same potential
as V
power lines (source)
) pins must always be connected to the external power
DD
(4)
(2)
Conditions
for the maximum allowed input voltage
for the maximum allowed input voltage
(3)
(1)
STM32F101x8, STM32F101xB
(1)
INJ(PIN)
(5)
Section 5.3.17: 12-bit ADC
–65 to +150
is the absolute sum of the
Min
IN
2.4
1.8
Value
IN
150
0
0
0
2
2
<V
<V
SS
SS
-5/+0
. I
Max.
− 25
± 25
150
150
± 5
25
. I
INJ(PIN)
Max
3.6
3.6
3.6
3.6
36
36
36
INJ(PIN)
must
must
Unit
MHz
Unit
Unit
°C
°C
mA
V
V
V